Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress the following warning displayed on building 32bit (i686) kernel.
===============================================================================
...
CC [M] fs/btrfs/extent_io.o
fs/btrfs/extent_io.c: In function ‘btrfs_free_io_failure_record’:
fs/btrfs/extent_io.c:2193:13: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
failrec = (struct io_failure_record *)state->private;
...
===============================================================================
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Reported-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Chris Mason <clm@fb.com>
When removing a block group we were deleting it from its space_info's
ro_bgs list without the correct protection - the space info's spinlock.
Fix this by doing the list delete while holding the spinlock of the
corresponding space info, which is the correct lock for any operation
on that list.
This issue was introduced in the 3.19 kernel by the following change:
Btrfs: move read only block groups onto their own list V2
commit 633c0aad4c
I ran into a kernel crash while a task was running statfs, which iterates
the space_info->ro_bgs list while holding the space info's spinlock,
and another task was deleting it from the same list, without holding that
spinlock, as part of the block group remove operation (while running the
function btrfs_remove_block_group). This happened often when running the
stress test xfstests/generic/038 I recently made.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
The address that should be freed is not 'ppath' but 'path'.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Reviewed-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Chris Mason <clm@fb.com>
The version merged to 3.19 did not handle errors from start_trancaction
and could pass an invalid pointer to commit_transaction.
Fixes: 6b5fe46dfa ("btrfs: do commit in sync_fs if there are pending changes")
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
This tc action allows you to retrieve the connection tracking mark
This action has been used heavily by openwrt for a few years now.
There are known limitations currently:
doesn't work for initial packets, since we only query the ct table.
Fine given use case is for returning packets
no implicit defrag.
frags should be rare so fix later..
won't work for more complex tasks, e.g. lookup of other extensions
since we have no means to store results
we still have a 2nd lookup later on via normal conntrack path.
This shouldn't break anything though since skb->nfct isn't altered.
V2:
remove unnecessary braces (Jiri)
change the action identifier to 14 (Jiri)
Fix some stylistic issues caught by checkpatch
V3:
Move module params to bottom (Cong)
Get rid of tcf_hashinfo_init and friends and conform to newer API (Cong)
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hauke Mehrtens says:
====================
bgmac: some fixes to napi usage
I compared the napi documentation with the bgmac driver and found some
problems in that driver. These two patches should fix the problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should complain in dmesg when journal recovery fails on account of
the descriptor block being corrupt, so that the diagnostic data can
be recovered.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: DSA fixes for bridge and ip-autoconf
These two patches address some real world use cases of the DSA master and slave
network devices.
You have already seen patch 1 previously and you rejected it since my
explanations were not good enough to provide a justification as to why it is
useful, hopefully this time my explanation is better.
Patch 2 solves a different, yet very real problem as well at the bridge layer
when using DSA network devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA-enabled master network devices with a switch tagging protocol should
strip the protocol specific format before handing the frame over to
higher layer.
When adding such a DSA master network device as a bridge member, we go
through the following code path when receiving a frame:
__netif_receive_skb_core
-> first ptype check against ptype_all is not returning any
handler for this skb
-> check and invoke rx_handler:
-> deliver frame to the bridge layer: br_handle_frame
DSA registers a ptype handler with the fake ETH_XDSA ethertype, which is
called *after* the bridge-layer rx_handler has run. br_handle_frame()
tries to parse the frame it received from the DSA master network device,
and will not be able to match any of its conditions and jumps straight
at the end of the end of br_handle_frame() and returns
RX_HANDLER_CONSUMED there.
Since we returned RX_HANDLER_CONSUMED, __netif_receive_skb_core() stops
RX processing for this frame and returns NET_RX_SUCCESS, so we never get
a chance to call our switch tag packet processing logic and deliver
frames to the DSA slave network devices, and so we do not get any
functional bridge members at all.
Instead of cluttering the bridge receive path with DSA-specific checks,
and rely on assumptions about how __netif_receive_skb_core() is
processing frames, we simply deny adding the DSA master network device
(conduit interface) as a bridge member, leaving only the slave DSA
network devices to be bridge members, since those will work correctly in
all circumstances.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to configure a network interface for kernel IP
auto-configuration is very simplistic, and does not handle the case
where a device is stacked onto another such as with DSA. This causes the
kernel not to open and configure the master network device in a DSA
switch tree, and therefore slave network devices using this master
network devices as conduit device cannot be open.
This restriction comes from a check in net/dsa/slave.c, which is
basically checking the master netdev flags for IFF_UP and returns
-ENETDOWN if it is not the case.
Automatically bringing-up DSA master network devices allows DSA slave
network devices to be used as valid interfaces for e.g: NFS root booting
by allowing kernel IP autoconfiguration to succeed on these interfaces.
On the reverse path, make sure we do not attempt to close a DSA-enabled
device as this would implicitely prevent the slave DSA network device
from operating.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_check_media() does not update the link (carrier) state or log link
changes when the link mode is forced. Drivers using the mii library
must do this themselves, but most of them do not.
Instead of changing them all, provide a sensible default behaviour
similar to mii_check_link() when the mode is forced.
via-rhine depends on it being a no-op in this case, so make its call
to mii_check_media() conditional.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
sh_eth fixes
I'm currently looking at Ethernet support on the R-Car H2 chip,
reviewing and testing the sh_eth driver. Here are fixes for two fairly
obvious bugs in the driver; I will probably have some more later.
These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Praveen Madhavan says:
====================
csiostor: Remove T4 FCoE support
We found a subtle issue with FCoE on T4 very late in the game
and decided not to productize FCoE on T4 and therefore there
are no customers that will be impacted by this change. FCoE is
supported on T5 cards.
Please apply on net-next since depends on previous commits.
Changes in v2:
- Make the commit message more clearer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have decided not to productize FCoE on T4.
Hence file is removed.
Signed-off-by: Praveen Madhavan <praveenm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found a subtle issue with FCoE on T4 very late in the game
and decided not to productize FCoE on T4 and therefore there
are no customers that will be impacted by this change. Hence
T4 FCoE support is removed. FCoE supported only on T5 cards.
changes in v2:
- Make the commit message more clearer.
Signed-off-by: Praveen Madhavan <praveenm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Karicheri says:
====================
net: Add Keystone NetCP ethernet driver support
The Network Coprocessor (NetCP) is a hardware accelerator that processes
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet
switch sub-module to send and receive packets. NetCP also includes a packet
accelerator (PA) module to perform packet classification operations such as
header matching, and packet modification operations such as checksum
generation. NetCP can also optionally include a Security Accelerator(SA)
capable of performing IPSec operations on ingress/egress packets.
Keystone SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and
1Gb/s rates per Ethernet port.
Both GBE and XGBE network processors supported using common driver. It
is also designed to handle future variants of NetCP.
version history
---------------
v7->v8
- Reworked comments against v7, related to checker warning.
- Patch 2/4 that has all of the driver code in v7 is now split into 3
patches based on functionality so that we have 3 smaller patches
review instead of a big patch.
- Patch for MAINTAINER is merged to 2/4 along with netcp core driver
- Separate patch (3/4) for 1G and (4/4) for 10G
- Removed big endian support for initial version (will add it later)
v6->v7
- Fixed some minor documentation error and also modified the netcp driver
to fix the set* functions to include correct le/be macros.
v5->v6
- updated version after incorporating comments [6] from David Miller,
David Laight & Geert Uytterhoeven on v5. I would like get this in
for v3.19 merge window if the latest version is acceptable.
v4->v5
- Sorry to spin v5 quickly but I missed few check-patch warnings which
were pointed by Joe Perches(thanks). I folded his changes [5] along with
few more check-patch warning fixes. I would like get this in for v3.18
merge window if David is happy with this version.
v3->v4
- Couple of fixes in in error path as pointed [4] out by David. Rest of
the patches are unchanged from v3.
v2->v3
- Update v3 after incorporating Jamal and David Miller's comment/suggestion
from earlier versions [1] [2]. After per the discussion here [3], the
controversial custom exports have been dropped now. And for future
future offload support additions, we will plug into generic frameworks
as an when they are available.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the NetCP gbe driver to support 10GbE subsystem
available in Keystone NetCP. The 3-port 10GbE switch sub-module contains
the following components:- 10GbE Switch, MDIO Module, 2 PCS-R Modules
(10GBase-R) and 2 SGMII modules (10/100/1000Base-T). The GBE driver
together with netcp core driver provides support for 10G Ethernet
on Keystone SoCs.
10GbE hardware spec is available at
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=spruhj5&fileType=pdf
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for 1G Ethernet driver based on Keystone
NetCP hardware. The gigabit Ethernet (GbE) switch subsystem is one of the main
components of the network coprocessor (NETCP) peripheral. The purpose of the
gigabit Ethernet switch subsystem in the NETCP is to provide an interface to
transfer data between the host device and another connected device in
compliance with the Ethernet protocol. GbE consists of 5 port Ethernet Switch
module, 4 Serial Gigabit Media Independent Interface (SGMII) modules, MDIO
module and SerDes.
Driver for 5 port GbE switch and SGMII module is added in this patch. These
hardware modules along with netcp core driver provides Network driver functions
for 1G Ethernet.
Detailed hardware spec is available at
http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network coprocessor (NetCP) is a hardware accelerator available in
Keystone SoCs that processes Ethernet packets. NetCP consists of following
hardware components
1 Gigabit Ethernet (GbE) subsystem with a Ethernet switch sub-module to
send and receive packets.
2 Packet Accelerator (PA) module to perform packet classification
operations such as header matching, and packet modification operations
such as checksum generation.
3 Security Accelerator(SA) capable of performing IPSec operations on
ingress/egress packets.
4 An optional 10 Gigabit Ethernet Subsystem (XGbE) which includes a
3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
per Ethernet port.
5 Packet DMA and Queue Management Subsystem (QMSS) to enqueue and dequeue
packets and DMA the packets between memory and NetCP hardware components
described above.
NetCP core driver make use of the Keystone Navigator driver API to allocate
DMA channel for the Ethenet device and to handle packet queue/de-queue,
Please refer API's in include/linux/soc/ti/knav_dma.h and
drivers/soc/ti/knav_qmss.h for details.
NetCP driver consists of NetCP core driver and at a minimum Gigabit
Ethernet (GBE) module (1) driver to implement the Network device function.
Other modules (2,3) can be optionally added to achieve supported hardware
acceleration function. The initial version of the driver include NetCP
core driver and GBE driver modules.
Please refer Documentation/devicetree/bindings/net/keystone-netcp.txt
for design of the driver.
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network coprocessor (NetCP) is a hardware accelerator that processes
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet
switch sub-module to send and receive packets. NetCP also includes a packet
accelerator (PA) module to perform packet classification operations such as
header matching, and packet modification operations such as checksum
generation. NetCP can also optionally include a Security Accelerator(SA)
capable of performing IPSec operations on ingress/egress packets.
Keystone SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and
1Gb/s rates per Ethernet port.
NetCP Subsystem device tree layout looks something like below:
-----------------------------
NetCP subsystem(10G or 1G)
-----------------------------
|
|-> NetCP Devices -> |
| |-> GBE/XGBE Switch
| |
| |-> Packet Accelerator
| |
| |-> Security Accelerator
|
|
|
|-> NetCP Interfaces -> |
|-> Ethernet Port 0
|
|-> Ethernet Port 1
|
|-> Ethernet Port 2
|
|-> Ethernet Port 3
Common driver supports GBE as well XGBE network processors.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: David Miller <davem@davemloft.net>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the attack vector and stop generating IPv6 Fragment Header for
paths with an MTU smaller than the minimum required IPv6 MTU
size (1280 byte) - called atomic fragments.
See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1]
for more information and how this "feature" can be misused.
[1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows booting the device with basic functionality.
Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.
Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:
http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to other omap variants, let's add dm816x support.
Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit c03abd8463 (net: ethernet: cpsw: don't requests IRQs we don't
use) left one build breakage when NET_POLL_CONTROLLER is enabled.
Fix this build break by referring to the correct irqs_table array.
Fixes: c03abd8463 (net: ethernet: cpsw: don't requests IRQs we don't use)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'link_netns'
Nicolas Dichtel says:
====================
netns: allow to identify peer netns
The goal of this serie is to be able to multicast netlink messages with an
attribute that identify a peer netns.
This is needed by the userland to interpret some information contained in
netlink messages (like IFLA_LINK value, but also some other attributes in case
of x-netns netdevice (see also
http://thread.gmane.org/gmane.linux.network/315933/focus=316064 and
http://thread.gmane.org/gmane.linux.kernel.containers/28301/focus=4239)).
Ids of peer netns can be set by userland via a new rtnl cmd RTM_NEWNSID. When
the kernel needs an id for a peer (for example when advertising a new x-netns
interface via netlink), if the user didn't allocate an id, one will be
automatically allocated.
These ids are stored per netns and are local (ie only valid in the netns where
they are set). To avoid allocating an int for each peer netns, I use
idr_for_each() to retrieve the id of a peer netns. Note that it will be possible
to add a table (struct net -> id) later to optimize this lookup if needed.
Patch 1/4 introduces the rtnetlink API mechanism to set and get these ids.
Patch 2/4 and 3/4 implements an example of how to use these ids when advertising
information about a x-netns interface.
And patch 4/4 shows that the netlink messages can be symetric between a GET and
a SET.
iproute2 patches are available, I can send them on demand.
Here is a small screenshot to show how it can be used by userland.
$ ip netns add foo
$ ip netns del foo
$ ip netns
$ touch /var/run/netns/init_net
$ mount --bind /proc/1/ns/net /var/run/netns/init_net
$ ip netns add foo
$ ip -n foo netns
foo
init_net
$ ip -n foo netns set init_net 0
$ ip -n foo netns set foo 1
$ ip netns
foo
init_net
$ ip -n foo netns
foo (id: 1)
init_net (id: 0)
$ ip -n foo link add ipip1 link-netnsid 0 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link ls ipip1
6: ipip1@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 0
$ ip netns
foo
init_net
$ ip -n foo link add ipip2 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link set ipip2 netns init_net
$ ip link ls ipip2
7: ipip2@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 0
$ ip netns
foo (id: 0)
init_net
v4 -> v5:
use rtnetlink instead of genetlink
allocate automatically an id if user didn't assign one
rename include/uapi/linux/netns.h to include/uapi/linux/net_namespace.h
add vxlan in patch #3
RFCv3 -> v4:
rebase on net-next
add copyright text in the new netns.h file
RFCv2 -> RFCv3:
ids are now defined by userland (via netlink). Ids are stored in each netns
(and they are local to this netns).
add get_link_net support for ip6 tunnels
netnsid is now a s32 instead of a u32
RFCv1 -> RFCv2:
remove useless ()
ids are now stored in the user ns. It's possible to get an id for a peer netns
only if the current netns and the peer netns have the same user ns parent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- we remove DEBUG_LL from sama5 defconfig as all SoC are not compatible
- enable ISI and selected sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUt/NQAAoJEAf03oE53VmQ0TsH+gOpauMKCPBXj4keev84Ec9k
WKq/6FhZb0YqNt0kfaaW8MIDzb2YVZMPgaEJ3UgN/hWfTACi3llIxe3IzwyBkyWS
c2GTpnAjt9RZm54cJ+hWhnOq5q2NX+JoQ0sB/bRfhQSCQqtWw8kNZuc4wYRe838A
q9hAJBjD221TiNjJgAgD9/EAXB/aBkos+hAky3pxfn6UcqrhaQKmQN70w2SOn9WV
D+I7DV+Njf4BtnVZoHX3c0ur3QDKOyFoyKe1e6DbgoOHNvDoJjbl622nsF955QMB
wRKj2gD/PIrI4k5S/4aQNdBwvCGJW03tpRxvIuE3rlQMO+sXhbG4AbQ0PoR6bl8=
=YfYF
-----END PGP SIGNATURE-----
Merge tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/defconfig
Merge "at91: defconfig for 3.20 #1" from Nicolas Ferre:
First batch of defconfig update for 3.20:
- we remove DEBUG_LL from sama5 defconfig as all SoC are not compatible
- enable ISI and selected sensors
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: sama5: enable atmel-isi and ov2640 in defconfig
ARM: at91/config: sama5: Remove DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>
We have pcf857x at least several boards. Let's enable it
as a loadable module.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some omaps have NOR flash as the rootfs but we're missing
physmap and physmap_of to properly support it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the ability to create a netdevice in a specified netns and
then move it into the final netns. In fact, it allows to have a symetry between
get and set rtnl messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new attribute (IFLA_LINK_NETNSID) which contains the 'link'
netns id when this netns is different from the netns where the interface
stands (for example for x-net interfaces like ip tunnels).
With this attribute, it's possible to interpret correctly all advertised
information (like IFLA_LINK, etc.).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUt+9WAAoJEAf03oE53VmQrlQH/2gLux3w9NMBm6GKDAJe3ZbY
JSiT9JIpcDmvVPXheeXQc0gZFGbfg8kcbx6mopPR/n6gAeP0npRApmQxS04M9M6b
HyAyj26s1h79WZOki7hhsIw6bhMCNDb7ODoDOw4F6U1/WWLh+uZY3fg+HO2CFBS8
wyDWKQQWAe0LvbaB44iw5cGsZ2+8/1rb5R7w7AqITjLTOGLvJZn50TYlY6hRrb+7
qfD0gqaRzX6axdtsGVNzkuYUuLQ3rE9IhgauhHlge9QT1Lkl4wfONnGiOFeIc+n0
tcHLb3BYBqOKDbOop+3ED3bqxcmobUIQIlEutvg5lnFkWeVYnXgkIFxHPpEK4K0=
=RH2X
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #1" from Nicolas Ferre:
First batch of DT changes for 3.20:
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
ARM: at91: dts: sama5d3: move the isi mck pin to mb
ARM: at91: dts: sama5d3: add missing pins of isi
ARM: at91: dts: sama5d3: split isi pinctrl
ARM: at91: dts: sama5d3: add isi clock
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
ARM: at91/dt: Add a dtsi for at91sam9xe
ARM: at91/dt: add SRAM nodes
ARM: at91/dt: at91rm9200ek: enable RTC
ARM: at91/dt: rm9200: add RTC node
ARM: at91/dt: at91sam9n12: Add RTC node
ARM: at91: sama5d4: Add SFR
ARM: at91: sama5d3: Add SFR
ARM: at91: Add Special Function Registers binding documentation
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
Signed-off-by: Olof Johansson <olof@lixom.net>
With this patch, a user can define an id for a peer netns by providing a FD or a
PID. These ids are local to the netns where it is added (ie valid only into this
netns).
The main function (ie the one exported to other module), peernet2id(), allows to
get the id of a peer netns. If no id has been assigned by the user, this
function allocates one.
These ids will be used in netlink messages to point to a peer netns, for example
in case of a x-netns interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Documentation for AT91 SoC
- Config options, files and functions removal to continue the big !DT
cleanup done in 3.19
- move of debug-macro.S to its usual location
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUt+1aAAoJEAf03oE53VmQPr8H/jsGkHpSoDIJEq6wbwseZvDo
dxLv096fuuaPuMGgzBgZ1bKhvbIkg4CHXQHmbmsx+oU+sVcCFomH+jwPaSFBIUJ8
Nn7lhk4lHcwLYUFEpruu+pVRoTPQRizLQIsSMKiUMRTkjS69SDTxaRjD1I6NVEsc
c91jPhiQm1+PDcgakkWTJasDHppcZz853gKvy97e2ICD28C7FnAzI6kpXM7bsH9n
j/p4WIGVcjlTm3D1wzhYA8CoXDdz6vCB5QCdbLHMypiSQPT0hx/jCg7Ti8kxgQE8
ZikqpD01bbq2eyZOPjWnfhNrxr6jgJUQAHToaD4co9vSSb51O0qVTE/b4igc76M=
=qsbn
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/cleanup
Merge "at91: cleanup for 3.20 #1" from Nicolas Ferre:
First batch of cleanup for 3.20:
- Documentation for AT91 SoC
- Config options, files and functions removal to continue the big !DT
cleanup done in 3.19
- move of debug-macro.S to its usual location
* tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to
HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE
and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG().
This problem is hard to reproduce making this patch hard to verify, but this
fix will prevent the race.
I have not been able to reproduce the problem, but here is a crash dump from
a 2.6.32 kernel.
On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE:
crash> struct ata_port.hsm_task_state ffff881c1121c000
hsm_task_state = 0
Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(),
which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value.
PID: 11053 TASK: ffff8816e846cae0 CPU: 0 COMMAND: "sshd"
#0 [ffff88008ba03960] machine_kexec at ffffffff81038f3b
#1 [ffff88008ba039c0] crash_kexec at ffffffff810c5d92
#2 [ffff88008ba03a90] oops_end at ffffffff8152b510
#3 [ffff88008ba03ac0] die at ffffffff81010e0b
#4 [ffff88008ba03af0] do_trap at ffffffff8152ad74
#5 [ffff88008ba03b50] do_invalid_op at ffffffff8100cf95
#6 [ffff88008ba03bf0] invalid_op at ffffffff8100bf9b
[exception RIP: ata_sff_hsm_move+317]
RIP: ffffffff813a77ad RSP: ffff88008ba03ca0 RFLAGS: 00010097
RAX: 0000000000000000 RBX: ffff881c1121dc60 RCX: 0000000000000000
RDX: ffff881c1121dd10 RSI: ffff881c1121dc60 RDI: ffff881c1121c000
RBP: ffff88008ba03d00 R8: 0000000000000000 R9: 000000000000002e
R10: 000000000001003f R11: 000000000000009b R12: ffff881c1121c000
R13: 0000000000000000 R14: 0000000000000050 R15: ffff881c1121dd78
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88008ba03d08] ata_sff_host_intr at ffffffff813a7fbd
#8 [ffff88008ba03d38] ata_sff_interrupt at ffffffff813a821e
#9 [ffff88008ba03d78] handle_IRQ_event at ffffffff810e6ec0
--- <IRQ stack> ---
[exception RIP: pipe_poll+48]
RIP: ffffffff81192780 RSP: ffff880f26d459b8 RFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff880f26d459c8 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff881a0539fa80
RBP: ffffffff8100bb8e R8: ffff8803b23324a0 R9: 0000000000000000
R10: ffff880f26d45dd0 R11: 0000000000000008 R12: ffffffff8109b646
R13: ffff880f26d45948 R14: 0000000000000246 R15: 0000000000000246
ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018
RIP: 00007f26017435c3 RSP: 00007fffe020c420 RFLAGS: 00000206
RAX: 0000000000000017 RBX: ffffffff8100b072 RCX: 00007fffe020c45c
RDX: 00007f2604a3f120 RSI: 00007f2604a3f140 RDI: 000000000000000d
RBP: 0000000000000000 R8: 00007fffe020e570 R9: 0101010101010101
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffe020e5f0
R13: 00007fffe020e5f4 R14: 00007f26045f373c R15: 00007fffe020e5e0
ORIG_RAX: 0000000000000017 CS: 0033 SS: 002b
Somewhere between the ata_sff_hsm_move() check and the ata_sff_host_intr() check, the value changed.
On examining the other cpus to see what else was running, another cpu was running the error handler
routines:
PID: 326 TASK: ffff881c11014aa0 CPU: 1 COMMAND: "scsi_eh_1"
#0 [ffff88008ba27e90] crash_nmi_callback at ffffffff8102fee6
#1 [ffff88008ba27ea0] notifier_call_chain at ffffffff8152d515
#2 [ffff88008ba27ee0] atomic_notifier_call_chain at ffffffff8152d57a
#3 [ffff88008ba27ef0] notify_die at ffffffff810a154e
#4 [ffff88008ba27f20] do_nmi at ffffffff8152b1db
#5 [ffff88008ba27f50] nmi at ffffffff8152aaa0
[exception RIP: _spin_lock_irqsave+47]
RIP: ffffffff8152a1ff RSP: ffff881c11a73aa0 RFLAGS: 00000006
RAX: 0000000000000001 RBX: ffff881c1121deb8 RCX: 0000000000000000
RDX: 0000000000000246 RSI: 0000000000000020 RDI: ffff881c122612d8
RBP: ffff881c11a73aa0 R8: ffff881c17083800 R9: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff881c1121c000
R13: 000000000000001f R14: ffff881c1121dd50 R15: ffff881c1121dc60
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
--- <NMI exception stack> ---
#6 [ffff881c11a73aa0] _spin_lock_irqsave at ffffffff8152a1ff
#7 [ffff881c11a73aa8] ata_exec_internal_sg at ffffffff81396fb5
#8 [ffff881c11a73b58] ata_exec_internal at ffffffff81397109
#9 [ffff881c11a73bd8] atapi_eh_request_sense at ffffffff813a34eb
Before it tried to acquire a spinlock, ata_exec_internal_sg() called ata_sff_flush_pio_task().
This function will set ap->hsm_task_state to HSM_ST_IDLE, and has no locking around setting this
value. ata_sff_flush_pio_task() can then race with the interrupt handler and potentially set
HSM_ST_IDLE at a fatal moment, which will trigger a kernel BUG.
v2: Fixup comment in ata_sff_flush_pio_task()
tj: Further updated comment. Use ap->lock instead of shost lock and
use the [un]lock_irq variant instead of the irqsave/restore one.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
so we drop Marco dts stuff, and add dts stuff for Atlas7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wbyB
-----END PGP SIGNATURE-----
Merge tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt
Merge "CSR atlas7 init dts for 3.20" from Barry Song:
Drop Marco and add init dts stuff for Atlas7
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
So we drop Marco dts stuff, and add dts stuff for Atlas7.
* tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: add init dts file for CSR atlas7 SoC
ARM: dts: drop MARCO platform DT stuff
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
__uvcg_fill_strm() called from __uvcg_iter_stream_cls()
might have advanced the "data" even if __uvcg_iter_stream_cls()
returns an error, so use a backup copy as an argument to kfree().
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update the MAINTAINERS entry for the dwc2 driver to show John Youn
as the new maintainer
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
