Xeon55xx fails to probe with this error message:
EDAC DEBUG: in drivers/edac/i7core_edac.c, line at 1660: MC: drivers/edac/i7core_edac.c: i7core_init()
EDAC i7core: Device not found: dev 00:00.0 PCI ID 8086:2c41
i7core_edac: probe of 0000:00:14.0 failed with error -22
This is due to the fact that, on Xeon35xx (and i7core), device 00.0 has
PCI ID 8086:2c40.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code changes the detection procedure of i7core_edac. Instead of
directly probing for MC registers, it probes for another register found
on Nehalem. If found, it tries to pick the first MC PCI BUS. This should
work fine with Xeon 35xx, but, on Xeon 55xx, this is at bus 254 and 255
that are not properly detected by the non-legacy PCI methods.
The new detection code scans specifically at buses 254 and 255 for the
Xeon 55xx devices.
This code has not tested yet. After working, a change at the code will
be needed, since the i7core is not yet ready for working with 2 sets of
MC.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The public Intel Xeon 5500 volume 2 datasheet describes, on page 53,
session 2.6.7 a register that can lock/unlock Memory Controller the
configuration register, called MC_CFG_CONTROL.
Adds support for it in the hope that software error injection would
work. With my tests with Xeon 35xx, there's still something missing.
With a program that does sequencial bit writes at dev 0.0, sometimes, it
produces error injection, after unblocking the MC_CFG_CONTROL (and,
sometimes, it just locks my testing machine).
I'll try later to discover by trial and error what's the register that
solves this issue on Xeon 35xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
edac_mce module is an interface module that gets mcelog data and
forwards to any registered edac module that expects to receive data via
mce.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is meant to support i7 core/i7core extreme desktop
processors and Xeon 35xx/55xx series with integrated memory controller.
It is likely that it can be expanded in the future to work with other
processor series based at the same Memory Controller design.
For now, it has just a few MCH status reads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The use of a memcpy() during a spinlock operation will cause very long
thread context switch delays if the flash chip bandwidth is low and the
data to be copied large, because a spinlock will disable preemption.
For example: A flash with 6,5 MB/s bandwidth will cause under ubifs,
which request sometimes 128 KiB (the flash erase size), a preemption delay of
20 milliseconds. High priority threads will not be served during this
time, regardless whether this threads access the flash or not. This behavior
breaks real time.
The patch changes all the use of spin_lock operations for xxxx->mutex
into mutex operations, which is exact what the name says and means.
I have checked the code of the drivers and there is no use of atomic
pathes like interrupt or timers. The mtdoops facility will also not be used
by this drivers. So it is dave to replace the spin_lock against mutex.
There is no performance regression since the mutex is normally not
acquired.
Changelog:
06.03.2010 First release
26.03.2010 Fix mutex[1] issue and tested it for compile failure
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
How to pick good mult/shift pairs has always been difficult to
describe to folks writing clocksource drivers, since it requires
careful tradeoffs in adjustment accuracy vs overflow limits.
Now, with the clocks_calc_mult_shift function, its much
easier. However, not many clocksources have converted to using that
function, and there is still the issue of the max interval length
assumption being made by each clocksource driver independently.
So this patch simplifies the registration process by having
clocksources be registered with a hz/khz value and the registration
function taking care of setting mult/shift.
This should take most of the confusion out of writing a clocksource
driver.
Additionally it also keeps the shift size tradeoff (more accuracy vs
longer possible nohz times) centralized so the timekeeping core can
keep track of the assumptions being made.
[ tglx: Coding style and comments fixed ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1273280858-30143-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Current s_volume_name has 16 bytes, which is too small as modern filesystem.
s_last_mounted resides just after s_volume_name and has 64 bytes.
s_last_mounted is historically came from ext2, but not used in nilfs2 at all.
Deleting s_last_mounted member and merging that space with s_volume_name
enlarge s_volume_name upto 80 bytes for volume label.
When user land tools see the old header for new disk, it will just ignore
additional bytes stored in s_last_mounted. While, old disk format has only
16 bytes label, it doesn't affects in case seeing the new header for old disk.
Signed-off-by: Jiro SEKIBA <jir@unicus.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
This adds a field to record the latest checkpoint number in the
nilfs_segment_summary structure. This will help to recover the latest
checkpoint number from logs on disk. This field is intended for
crucial cases in which super blocks have lost pointer to the latest
log.
Even though this will change the disk format, both backward and
forward compatibility is preserved by a size field prepared in the
segment summary header.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
This kills the following checkpatch warnings:
WARNING: please, no space before tabs
+^I__le32^Is_first_ino; ^I^I/* First non-reserved inode */$
WARNING: please, no space before tabs
+^I__le16 s_inode_size; ^I^I/* Size of an inode */$
WARNING: please, no space before tabs
+^Ichar^Is_volume_name[16]; ^I/* volume name */$
WARNING: please, no space before tabs
+^Ichar^Is_last_mounted[64]; ^I/* directory where last mounted */$
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
The comment of struct nilfs_dat_entry is mismatched, fix it.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
For the ondemand cpufreq governor, it is desired that the iowait
time is microaccounted in a similar way as idle time is.
This patch introduces the infrastructure to account and expose
this information via the get_cpu_iowait_time_us() function.
[akpm@linux-foundation.org: fix CONFIG_NO_HZ=n build]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082523.284feab6@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the only user of ts->idle_lastupdate is
update_ts_time_stats(), the entire field can be eliminated.
In update_ts_time_stats(), idle_lastupdate is first set to
"now", and a few lines later, the only user is an if() statement
that assigns a variable either to "now" or to
ts->idle_lastupdate, which has the value of "now" at that point.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082439.2fab0b4f@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When !CONFIG_SMP, cpu_stop functions weren't defined at all which
could lead to build failures if UP code uses cpu_stop facility. Add
dummy cpu_stop implementation for UP. The waiting variants execute
the work function directly with preempt disabled and
stop_one_cpu_nowait() schedules a workqueue work.
Makefile and ifdefs around stop_machine implementation are updated to
accomodate CONFIG_SMP && !CONFIG_STOP_MACHINE case.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ingo Molnar <mingo@elte.hu>
Commit 23caaf19b ("ALSA: usb-mixer: Add support for Audio Class v2.0")
broke support for Class1 devices due to two faulty changes. This patch
fixes it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-and-Tested-by: The Source <thesourcehim@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: create rcu_my_thread_group_empty() wrapper
memcg: css_id() must be called under rcu_read_lock()
cgroup: Check task_lock in task_subsys_state()
sched: Fix an RCU warning in print_task()
cgroup: Fix an RCU warning in alloc_css_id()
cgroup: Fix an RCU warning in cgroup_path()
KEYS: Fix an RCU warning in the reading of user keys
KEYS: Fix an RCU warning
Currently (all tested with hwsim) you can do stupid
things like setting up an AP on a certain channel,
then adding another virtual interface and making
that associate on another channel -- this will make
the beaconing to move channel but obviously without
the necessary IEs data update.
In order to improve this situation, first make the
configuration APIs (cfg80211 and nl80211) aware of
multi-channel operation -- we'll eventually need
that in the future anyway. There's one userland API
change and one API addition. The API change is that
now SET_WIPHY must be called with virtual interface
index rather than only wiphy index in order to take
effect for that interface -- luckily all current
users (hostapd) do that. For monitor interfaces, the
old setting is preserved, but monitors are always
slaved to other devices anyway so no guarantees.
The second userland API change is the introduction
of a per virtual interface SET_CHANNEL command, that
hostapd should use going forward to make it easier
to understand what's going on (it can automatically
detect a kernel with this command).
Other than mac80211, no existing cfg80211 drivers
are affected by this change because they only allow
a single virtual interface.
mac80211, however, now needs to be aware that the
channel settings are per interface now, and needs
to disallow (for now) real multi-channel operation,
which is another important part of this patch.
One of the immediate benefits is that you can now
start hostapd to operate on a hardware that already
has a connection on another virtual interface, as
long as you specify the same channel.
Note that two things are left unhandled (this is an
improvement -- not a complete fix):
* different HT/no-HT modes
currently you could start an HT AP and then
connect to a non-HT network on the same channel
which would configure the hardware for no HT;
that can be fixed fairly easily
* CSA
An AP we're connected to on a virtual interface
might indicate switching channels, and in that
case we would follow it, regardless of how many
other interfaces are operating; this requires
more effort to fix but is pretty rare after all
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add group scheduling transactional APIs to struct pmu.
These APIs will be implemented in arch code, based on Peter's idea as
below.
> the idea behind hw_perf_group_sched_in() is to not perform
> schedulability tests on each event in the group, but to add the group
> as a whole and then perform one test.
>
> Of course, when that test fails, you'll have to roll-back the whole
> group again.
>
> So start_txn (or a better name) would simply toggle a flag in the pmu
> implementation that will make pmu::enable() not perform the
> schedulablilty test.
>
> Then commit_txn() will perform the schedulability test (so note the
> method has to have a !void return value.
>
> This will allow us to use the regular
> kernel/perf_event.c::group_sched_in() and all the rollback code.
> Currently each hw_perf_group_sched_in() implementation duplicates all
> the rolllback code (with various bugs).
->start_txn:
Start group events scheduling transaction, set a flag to make
pmu::enable() not perform the schedulability test, it will be performed
at commit time.
->commit_txn:
Commit group events scheduling transaction, perform the group
schedulability as a whole
->cancel_txn:
Stop group events scheduling transaction, clear the flag so
pmu::enable() will perform the schedulability test.
Reviewed-by: Stephane Eranian <eranian@google.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1272002160.5707.60.camel@minggr.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename perf_event_attr::precise to perf_event_attr::precise_ip and
widen it to 2 bits. This new field describes the required precision of
the PERF_SAMPLE_IP field:
0 - SAMPLE_IP can have arbitrary skid
1 - SAMPLE_IP must have constant skid
2 - SAMPLE_IP requested to have 0 skid
3 - SAMPLE_IP must have 0 skid
And modify the Intel PEBS code accordingly. The PEBS implementation
now supports up to precise_ip == 2, where we perform the IP fixup.
Also s/PERF_RECORD_MISC_EXACT/&_IP/ to clarify its meaning, this bit
should be set for each PERF_SAMPLE_IP field known to match the actual
instruction triggering the event.
This new scheme allows for a PEBS mode that uses the buffer for more
than a single event.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Both Stephane and Corey reported that PERF_FORMAT_GROUP didn't work
as expected if the task the counters were attached to quit before
the read() call.
The cause is that we unconditionally destroy the grouping when we
remove counters from their context. Fix this by only doing this when
we free the counter itself.
Reported-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1273160566.5605.404.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
eth_type_trans() & get_rps_cpus() currently need two 64bytes cache
lines in packet to compute rxhash.
Increasing NET_SKB_PAD from 32 to 64 reduces the need to one cache
line only, and makes RPS faster.
NET_IP_ALIGN(2) + ethernet_header(14) + IP_header(20/40) + ports(8)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently migration_thread is serving three purposes - migration
pusher, context to execute active_load_balance() and forced context
switcher for expedited RCU synchronize_sched. All three roles are
hardcoded into migration_thread() and determining which job is
scheduled is slightly messy.
This patch kills migration_thread and replaces all three uses with
cpu_stop. The three different roles of migration_thread() are
splitted into three separate cpu_stop callbacks -
migration_cpu_stop(), active_load_balance_cpu_stop() and
synchronize_sched_expedited_cpu_stop() - and each use case now simply
asks cpu_stop to execute the callback as necessary.
synchronize_sched_expedited() was implemented with private
preallocated resources and custom multi-cpu queueing and waiting
logic, both of which are provided by cpu_stop.
synchronize_sched_expedited_count is made atomic and all other shared
resources along with the mutex are dropped.
synchronize_sched_expedited() also implemented a check to detect cases
where not all the callback got executed on their assigned cpus and
fall back to synchronize_sched(). If called with cpu hotplug blocked,
cpu_stop already guarantees that and the condition cannot happen;
otherwise, stop_machine() would break. However, this patch preserves
the paranoid check using a cpumask to record on which cpus the stopper
ran so that it can serve as a bisection point if something actually
goes wrong theree.
Because the internal execution state is no longer visible,
rcu_expedited_torture_stats() is removed.
This patch also renames cpu_stop threads to from "stopper/%d" to
"migration/%d". The names of these threads ultimately don't matter
and there's no reason to make unnecessary userland visible changes.
With this patch applied, stop_machine() and sched now share the same
resources. stop_machine() is faster without wasting any resources and
sched migration users are much cleaner.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: Josh Triplett <josh@freedesktop.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Reimplement stop_machine using cpu_stop. As cpu stoppers are
guaranteed to be available for all online cpus,
stop_machine_create/destroy() are no longer necessary and removed.
With resource management and synchronization handled by cpu_stop, the
new implementation is much simpler. Asking the cpu_stop to execute
the stop_cpu() state machine on all online cpus with cpu hotplug
disabled is enough.
stop_machine itself doesn't need to manage any global resources
anymore, so all per-instance information is rolled into struct
stop_machine_data and the mutex and all static data variables are
removed.
The previous implementation created and destroyed RT workqueues as
necessary which made stop_machine() calls highly expensive on very
large machines. According to Dimitri Sivanich, preventing the dynamic
creation/destruction makes booting faster more than twice on very
large machines. cpu_stop resources are preallocated for all online
cpus and should have the same effect.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Implement a simplistic per-cpu maximum priority cpu monopolization
mechanism. A non-sleeping callback can be scheduled to run on one or
multiple cpus with maximum priority monopolozing those cpus. This is
primarily to replace and unify RT workqueue usage in stop_machine and
scheduler migration_thread which currently is serving multiple
purposes.
Four functions are provided - stop_one_cpu(), stop_one_cpu_nowait(),
stop_cpus() and try_stop_cpus().
This is to allow clean sharing of resources among stop_cpu and all the
migration thread users. One stopper thread per cpu is created which
is currently named "stopper/CPU". This will eventually replace the
migration thread and take on its name.
* This facility was originally named cpuhog and lived in separate
files but Peter Zijlstra nacked the name and thus got renamed to
cpu_stop and moved into stop_machine.c.
* Better reporting of preemption leak as per Peter's suggestion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Some RCU-lockdep splat repairs need to know whether they are running
in a single-threaded process. Unfortunately, the thread_group_empty()
primitive is defined in sched.h, and can induce #include hell. This
commit therefore introduces a rcu_my_thread_group_empty() wrapper that
is defined in rcupdate.c, thus avoiding the need to include sched.h
everywhere.
Signed-off-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
This whole patchset is for adding netpoll support to bridge and bonding
devices. I already tested it for bridge, bonding, bridge over bonding,
and bonding over bridge. It looks fine now.
To make bridge and bonding support netpoll, we need to adjust
some netpoll generic code. This patch does the following things:
1) introduce two new priv_flags for struct net_device:
IFF_IN_NETPOLL which identifies we are processing a netpoll;
IFF_DISABLE_NETPOLL is used to disable netpoll support for a device
at run-time;
2) introduce one new method for netdev_ops:
->ndo_netpoll_cleanup() is used to clean up netpoll when a device is
removed.
3) introduce netpoll_poll_dev() which takes a struct net_device * parameter;
export netpoll_send_skb() and netpoll_poll_dev() which will be used later;
4) hide a pointer to struct netpoll in struct netpoll_info, ditto.
5) introduce ->real_dev for struct netpoll.
6) introduce a new status NETDEV_BONDING_DESLAE, which is used to disable
netconsole before releasing a slave, to avoid deadlocks.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than one header is included under CREATE_TRACE_POINTS
the DECLARE_TRACE() macro is not defined back to its original meaning
and the second include will fail to initialize the TRACE_EVENT()
and DECLARE_TRACE() correctly.
To fix this the tracepoint.h file moves the define of DECLARE_TRACE()
out of the #ifdef _LINUX_TRACEPOINT_H protection (just like the
define of the TRACE_EVENT()). This way the define_trace.h will undef
the DECLARE_TRACE() at the end and allow new headers to start
from scratch.
This patch also requires fixing the include/events/napi.h
It currently uses DECLARE_TRACE() and should be converted to a TRACE_EVENT()
format. But I'll leave that change to the authors of that file.
But since the napi.h file depends on using the CREATE_TRACE_POINTS
and does not define its own DEFINE_TRACE() it must use the define_trace.h
method instead.
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With following patch I can reach maximum rate of my pktgen+udpsink
simulator :
- 'old' machine : dual quad core E5450 @3.00GHz
- 64 UDP rx flows (only differ by destination port)
- RPS enabled, NIC interrupts serviced on cpu0
- rps dispatched on 7 other cores. (~130.000 IPI per second)
- SLAB allocator (faster than SLUB in this workload)
- tg3 NIC
- 1.080.000 pps without a single drop at NIC level.
Idea is to add two prefetchw() calls in __alloc_skb(), one to prefetch
first sk_buff cache line, the second to prefetch the shinfo part.
Also using one memset() to initialize all skb_shared_info fields instead
of one by one to reduce number of instructions, using long word moves.
All skb_shared_info fields before 'dataref' are cleared in
__alloc_skb().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In perverse acpi implementations the isa irqs are not identity mapped
to the first 16 gsi. Furthermore at least the extended interrupt
resource capability may return gsi's and not isa irqs. So since
what we get from acpi is a gsi teach acpi_get_overrride_irq to
operate on a gsi instead of an isa_irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-2-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There are a number of cases where the current code makes the assumption
that isa irqs identity map to the first 16 acpi global system intereupts.
In most instances that assumption is correct as that is the required
behaviour in dual i8259 mode and the default behavior in ioapic mode.
However there are some systems out there that take advantage of acpis
interrupt remapping for the isa irqs to have a completely different
mapping of isa_irq to gsi.
Introduce acpi_isa_irq_to_gsi to perform this mapping explicitly in the
code that needs it. Initially this will be just the current assumed
identity mapping to ensure it's introduction does not cause regressions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-1-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fix function prototype visibility issues when compiling for non-x86
architectures. Tested with crosstool
(ftp://ftp.kernel.org/pub/tools/crosstool/) with alpha, ia64 and sparc
targets.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100503130736.GD26107@aftab>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
