Change the callchain context entries to u16, so as to gain some space.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090406094517.457320003@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the userspace read method.
Paul noted that:
- userspace cannot observe ->lock & 1 on the same cpu.
- we need a barrier() between reading ->lock and ->index
to ensure we read them in that prticular order.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090406094517.368446033@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The request inherits the unplug flag from the bio, but it isn't actually
used. The bio flag stops at __make_request(), which tells it to unplug
after submission. Passing it on to the request doesn't make any sense.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This forces in_flight to be zero when turning off or on the I/O stat
accounting and stops updating I/O stats in attempt_merge() when
accounting is turned off.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add support to the SQ-905 driver to pass back to user space the
sensor orientation information obtained from the camera during init.
Modifies gspca and the videodev2.h header to create the necessary
API.
[mchehab@redhat.com: Changed "Output is" to "Frames are" at the comments, as suggested at LMML]
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is common code shared between the IDE and libata implementations
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
Fixes:
In file included from drivers/serial/mux.c:37:
include/linux/serial_core.h: In function 'uart_handle_sysrq_char':
include/linux/serial_core.h:467: error: 'struct uart_port' has no member named 'sysrq'
include/linux/serial_core.h:468: error: 'struct uart_port' has no member named 'sysrq'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements basic support for all 843x RS232 devices, but does not
add DMA support. This means that sustained data transfers at high baud
rates may not be possible on multiple ports simultaneously.
Signed-off-by: Shawn Bohrer <shawn.bohrer@ni.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kmemtrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kmemtrace: trace kfree() calls with NULL or zero-length objects
kmemtrace: small cleanups
kmemtrace: restore original tracing data binary format, improve ABI
kmemtrace: kmemtrace_alloc() must fill type_id
kmemtrace: use tracepoints
kmemtrace, rcu: don't include unnecessary headers, allow kmemtrace w/ tracepoints
kmemtrace, rcu: fix rcupreempt.c data structure dependencies
kmemtrace, rcu: fix rcu_tree_trace.c data structure dependencies
kmemtrace, rcu: fix linux/rcutree.h and linux/rcuclassic.h dependencies
kmemtrace, mm: fix slab.h dependency problem in mm/failslab.c
kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_unlzma.c
kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_bunzip2.c
kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_inflate.c
kmemtrace, squashfs: fix slab.h dependency problem in squasfs
kmemtrace, befs: fix slab.h dependency problem
kmemtrace, security: fix linux/key.h header file dependencies
kmemtrace, fs: fix linux/fdtable.h header file dependencies
kmemtrace, fs: uninline simple_transaction_set()
kmemtrace, fs, security: move alloc_secdata() and free_secdata() to linux/security.h
* 'for-2.6.30' of git://linux-nfs.org/~bfields/linux: (81 commits)
nfsd41: define nfsd4_set_statp as noop for !CONFIG_NFSD_V4
nfsd41: define NFSD_DRC_SIZE_SHIFT in set_max_drc
nfsd41: Documentation/filesystems/nfs41-server.txt
nfsd41: CREATE_EXCLUSIVE4_1
nfsd41: SUPPATTR_EXCLCREAT attribute
nfsd41: support for 3-word long attribute bitmask
nfsd: dynamically skip encoded fattr bitmap in _nfsd4_verify
nfsd41: pass writable attrs mask to nfsd4_decode_fattr
nfsd41: provide support for minor version 1 at rpc level
nfsd41: control nfsv4.1 svc via /proc/fs/nfsd/versions
nfsd41: add OPEN4_SHARE_ACCESS_WANT nfs4_stateid bmap
nfsd41: access_valid
nfsd41: clientid handling
nfsd41: check encode size for sessions maxresponse cached
nfsd41: stateid handling
nfsd: pass nfsd4_compound_state* to nfs4_preprocess_{state,seq}id_op
nfsd41: destroy_session operation
nfsd41: non-page DRC for solo sequence responses
nfsd41: Add a create session replay cache
nfsd41: create_session operation
...
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: introduce lp5521 led driver
leds: just ignore invalid GPIOs in leds-gpio
leds: Fix &&/|| confusion in leds-pca9532.c
leds: move h1940-leds's probe function to .devinit.text
leds: remove an unnecessary "goto" on drivers/leds/leds-s3c24.c
leds: add BD2802GU LED driver
leds: remove experimental flag from leds-clevo-mail
leds: Prevent multiple LED triggers with the same name
leds: Add gpio-led trigger
leds: Add rb532 LED driver for the User LED
leds: Add suspend/resume state flags to leds-gpio
leds: simple driver for pwm driven LEDs
leds: Fix leds-gpio driver multiple module_init/exit usage
leds: Add dac124s085 driver
leds: allow led-drivers to use a variable range of brightness values
leds: Add openfirmware platform device support
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixes the following compiler error:
fs/nfsd/nfssvc.c: In function 'set_max_drc':
fs/nfsd/nfssvc.c:240: error: 'NFSD_DRC_SIZE_SHIFT' undeclared
CONFIG_NFSD_V4 is not set
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The new i2c binding model makes the client_register and
client_unregister methods of struct i2c_adapter useless, so we can
remove them with the rest of the legacy model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes. This RGB controller incorporates
lighting patterns and illuminates.
This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state. And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.
Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add an option to preserve LED state when suspending/resuming to the LED
gpio driver. Based on a suggestion from Robert Jarzmik.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add a simple driver for pwm driver LEDs. pwm_id and period can be defined
in board file. It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch allows drivers to override the default maximum brightness value
of 255. We take care to preserve backwards-compatibility as much as
possible, so that user-space ABI doesn't change for existing drivers.
LED trigger code has also been updated to use the per-LED maximum.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
By default, CFQ will anticipate more IO from a given io context if the
previously completed IO was sync. This used to be fine, since the only
sync IO was reads and O_DIRECT writes. But with more "normal" sync writes
being used now, we don't want to anticipate for those.
Add a bio/request flag that informs the IO scheduler that this is a sync
request that we should not idle for. Introduce WRITE_ODIRECT specifically
for O_DIRECT writes, and make sure that the other sync writes set this
flag.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(S)WRITE_SYNC always unplugs the device right after IO submission.
Sometimes we want to build up a queue before doing so, so add
variants that explicitly DON'T unplug the queue. The caller must
then do that after submitting all the IO.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes sure that we never wait on async IO for sync requests, instead
of doing the split on writes vs reads.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
PI Futexes and their underlying rt_mutex cannot be left ownerless if
there are pending waiters as this will break the PI boosting logic, so
the standard requeue commands aren't sufficient. The new commands
properly manage pi futex ownership by ensuring a futex with waiters
has an owner at all times. This will allow glibc to properly handle
pi mutexes with pthread_condvars.
The approach taken here is to create two new futex op codes:
FUTEX_WAIT_REQUEUE_PI:
Tasks will use this op code to wait on a futex (such as a non-pi waitqueue)
and wake after they have been requeued to a pi futex. Prior to returning to
userspace, they will acquire this pi futex (and the underlying rt_mutex).
futex_wait_requeue_pi() is the result of a high speed collision between
futex_wait() and futex_lock_pi() (with the first part of futex_lock_pi() being
done by futex_proxy_trylock_atomic() on behalf of the top_waiter).
FUTEX_REQUEUE_PI (and FUTEX_CMP_REQUEUE_PI):
This call must be used to wake tasks waiting with FUTEX_WAIT_REQUEUE_PI,
regardless of how many tasks the caller intends to wake or requeue.
pthread_cond_broadcast() should call this with nr_wake=1 and
nr_requeue=INT_MAX. pthread_cond_signal() should call this with nr_wake=1 and
nr_requeue=0. The reason being we need both callers to get the benefit of the
futex_proxy_trylock_atomic() routine. futex_requeue() also enqueues the
top_waiter on the rt_mutex via rt_mutex_start_proxy_lock().
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Paul noted that we don't need SMP barriers for the mmap() counter read
because its always on the same cpu (otherwise you can't access the hw
counter anyway).
So remove the SMP barriers and replace them with regular compiler
barriers.
Further, update the comment to include a race free method of reading
said hardware counter. The primary change is putting the pmc_read
inside the seq-loop, otherwise we can still race and read rubbish.
Noticed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Orig-LKML-Reference: <20090402091319.577951445@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Put in counts to tell which ips belong to what context.
-----
| | hv
| --
nr | | kernel
| --
| | user
-----
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Orig-LKML-Reference: <20090402091319.493101305@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
By request, provide a way to request a wakeup every 'n' events instead
of every page of output.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Orig-LKML-Reference: <20090402091319.323309784@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Per suggestion from Paul, move the event overflow bits to record_type
and sanitize the enums a bit.
Breaks the ABI -- again ;-)
Suggested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Orig-LKML-Reference: <20090402091319.151921176@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide the generic callchain support bits. If hw_event->callchain is
set the arch specific perf_callchain() function is called upon to
provide a perf_callchain_entry structure filled with the current
callchain.
If it does so, it is added to the overflow output event.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090330171024.254266860@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Breaks ABI yet again :-)
Change the event type so that [0, 2^31-1] are regular event types, but
[2^31, 2^32-1] forms a bitmask for overflow events.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090330171024.047961770@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the profiling information returns userspace IPs but no way
to correlate them to userspace code. Userspace could look into
/proc/$pid/maps but that might not be current or even present anymore
at the time of analyzing the IPs.
Therefore provide means to track the mmap information and provide it
in the output stream.
XXX: only covers mmap()/munmap(), mremap() and mprotect() are missing.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Orig-LKML-Reference: <20090330171023.417259499@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It just occured to me it is possible to have multiple contending
updates of the userpage (mmap information vs overflow vs counter).
This would break the seqlock logic.
It appear the arch code uses this from NMI context, so we cannot
possibly serialize its use, therefore separate the data_head update
from it and let it return to its original use.
The arch code needs to make sure there are no contending callers by
disabling the counter before using it -- powerpc appears to do this
nicely.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090330171023.241410660@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While going over the wakeup code I noticed delayed wakeups only work
for hardware counters but basically all software counters rely on
them.
This patch unifies and generalizes the delayed wakeup to fix this
issue.
Since we're dealing with NMI context bits here, use a cmpxchg() based
single link list implementation to track counters that have pending
wakeups.
[ This should really be generic code for delayed wakeups, but since we
cannot use cmpxchg()/xchg() in generic code, I've let it live in the
perf_counter code. -- Eric Dumazet could use it to aggregate the
network wakeups. ]
Furthermore, the x86 method of using TIF flags was flawed in that its
quite possible to end up setting the bit on the idle task, loosing the
wakeup.
The powerpc method uses per-cpu storage and does appear to be
sufficient.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090330171023.153932974@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: new functionality
Currently, if there are more counters enabled than can fit on the CPU,
the kernel will multiplex the counters on to the hardware using
round-robin scheduling. That isn't too bad for sampling counters, but
for counting counters it means that the value read from a counter
represents some unknown fraction of the true count of events that
occurred while the counter was enabled.
This remedies the situation by keeping track of how long each counter
is enabled for, and how long it is actually on the cpu and counting
events. These times are recorded in nanoseconds using the task clock
for per-task counters and the cpu clock for per-cpu counters.
These values can be supplied to userspace on a read from the counter.
Userspace requests that they be supplied after the counter value by
setting the PERF_FORMAT_TOTAL_TIME_ENABLED and/or
PERF_FORMAT_TOTAL_TIME_RUNNING bits in the hw_event.read_format field
when creating the counter. (There is no way to change the read format
after the counter is created, though it would be possible to add some
way to do that.)
Using this information it is possible for userspace to scale the count
it reads from the counter to get an estimate of the true count:
true_count_estimate = count * total_time_enabled / total_time_running
This also lets userspace detect the situation where the counter never
got to go on the cpu: total_time_running == 0.
This functionality has been requested by the PAPI developers, and will
be generally needed for interpreting the count values from counting
counters correctly.
In the implementation, this keeps 5 time values (in nanoseconds) for
each counter: total_time_enabled and total_time_running are used when
the counter is in state OFF or ERROR and for reporting back to
userspace. When the counter is in state INACTIVE or ACTIVE, it is the
tstamp_enabled, tstamp_running and tstamp_stopped values that are
relevant, and total_time_enabled and total_time_running are determined
from them. (tstamp_stopped is only used in INACTIVE state.) The
reason for doing it like this is that it means that only counters
being enabled or disabled at sched-in and sched-out time need to be
updated. There are no new loops that iterate over all counters to
update total_time_enabled or total_time_running.
This also keeps separate child_total_time_running and
child_total_time_enabled fields that get added in when reporting the
totals to userspace. They are separate fields so that they can be
atomic. We don't want to use atomics for total_time_running,
total_time_enabled etc., because then we would have to use atomic
sequences to update them, which are slower than regular arithmetic and
memory accesses.
It is possible to measure total_time_running by adding a task_clock
counter to each group of counters, and total_time_enabled can be
measured approximately with a top-level task_clock counter (though
inaccuracies will creep in if you need to disable and enable groups
since it is not possible in general to disable/enable the top-level
task_clock counter simultaneously with another group). However, that
adds extra overhead - I measured around 15% increase in the context
switch latency reported by lat_ctx (from lmbench) when a task_clock
counter was added to each of 2 groups, and around 25% increase when a
task_clock counter was added to each of 4 groups. (In both cases a
top-level task-clock counter was also added.)
In contrast, the code added in this commit gives better information
with no overhead that I could measure (in fact in some cases I
measured lower times with this code, but the differences were all less
than one standard deviation).
[ v2: address review comments by Andrew Morton. ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Orig-LKML-Reference: <18890.6578.728637.139402@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allow cpu wide counters to profile userspace by providing what process
the sample belongs to.
This raises the first issue with the output type, lots of these
options: group, tid, callchain, etc.. are non-exclusive and could be
combined, suggesting a bitfield.
However, things like the mmap() data stream doesn't fit in that.
How to split the type field...
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Orig-LKML-Reference: <20090325113317.013775235@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide a {type,size} header for each output entry.
This should provide extensible output, and the ability to mix multiple streams.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Orig-LKML-Reference: <20090325113316.831607932@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix kerneltop 100% CPU usage
Only return a poll event when there's actually been one, poll_wait()
doesn't actually wait for the waitq you pass it, it only enqueues
you on it.
Only once all FDs have been iterated and none of thm returned a
poll-event will it schedule().
Also make it return POLL_HUP when there's not mmap() area to read from.
Further, fix a silly bug in the write code.
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Orig-LKML-Reference: <1237897096.24918.181.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Rework the perfcounter output ABI
use sys_read() only for instant data and provide mmap() output for all
async overflow data.
The first mmap() determines the size of the output buffer. The mmap()
size must be a PAGE_SIZE multiple of 1+pages, where pages must be a
power of 2 or 0. Further mmap()s of the same fd must have the same
size. Once all maps are gone, you can again mmap() with a new size.
In case of 0 extra pages there is no data output and the first page
only contains meta data.
When there are data pages, a poll() event will be generated for each
full page of data. Furthermore, the output is circular. This means
that although 1 page is a valid configuration, its useless, since
we'll start overwriting it the instant we report a full page.
Future work will focus on the output format (currently maintained)
where we'll likey want each entry denoted by a header which includes a
type and length.
Further future work will allow to splice() the fd, also containing the
async overflow data -- splice() would be mutually exclusive with
mmap() of the data.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090323172417.470536358@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Much like the atomic_dec_and_lock() function in which we take an hold a
spin_lock if we drop the atomic to 0 this function takes and holds the
mutex if we dec the atomic to 0.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090323172417.410913479@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
