An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet MAC drivers using the PHY library require the hardcoding
of link parameters when interfaced to a switch device, SFP module,
switch to switch port, etc. This has typically lead to various ad-hoc
implementations looking like this:
- using a "fixed PHY" emulated device, which will provide link
indication towards the Ethernet MAC driver and hardware
- pretend there is no PHY and hardcode link parameters, ala mv643x_eth
Based on that, it is desireable to have the PHY drivers advertise the
correct link parameters, just like regular Ethernet PHYs towards their
CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able
to tell whether this link should be monitored or not. In the context
of an Ethernet switch, SFP module, switch to switch link, we do not
need to monitor this link since it should be always up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
generalize FETCH_FUNC_NAME(memory, string) into
strncpy_from_unsafe() and fix sparse warnings that were
present in original implementation.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting. Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.
Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose. However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.
Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so. In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:
2) Packets with a destination IP (DIP) address in the 224.0.0.X
range which are not IGMP must be forwarded on all ports.
IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
echo 1 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OPENVSWITCH is set, and CONFIG_NETFILTER is not set, the
openvswitch IPv6 fragmentation handling cannot refer to ipv6_ops because
it isn't defined. Add a dummy version to avoid #ifdefs in source files.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this helper so code can easily figure out if netdev is openswitch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this helper so code can easily figure out if netdev is a bridge.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add info that is passed along with NETDEV_CHANGEUPPER event.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is the NFC pull request for 4.3.
With this one we have:
- A new driver for Samsung's S3FWRN5 NFC chipset. In order to
properly support this driver, a few NCI core routines needed
to be exported. Future drivers like Intel's Fields Peak will
benefit from this.
- SPI support as a physical transport for STM st21nfcb.
- An additional netlink API for sending replies back to userspace
from vendor commands.
- 2 small fixes for TI's trf7970a
- A few st-nci fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV1l7oAAoJEIqAPN1PVmxK7DwP+QF3A6wCBzaNQKcla6LOl+Ru
lGquPpFyihlDT/916IP7MnMNZYOP3ENdGll5lKts2yKxuty327Bb2UWNkaFP63Ei
+zZwhoZXwh6dbK35kwnd87Cwgn0E8vTF+zHhC2MmP8uGDIgOuevb//2GBDayG88T
rw4QMZsunT4o9x/bNK1uTlYaKPDs5pxXYFYUPXOQ2F5GqpUVFag3pLbZcJhpSZg7
9Y1KNLxwi/1rwO90JTXH9CQ+oWgVcH86nIlzqGznxgNdOoCF/V/0hdGlTzj8sE6T
A3a0Qy1gaWQw9+9QoqE7YWu6JfEIgEhRgFx8dm4SsmUbrnlmgYBavEFeG7++1AG5
QByWh/h2po0MysNRCfhey2EExlZgdvc1WyLQlS+0w+aWmM5MYq+J4lx+sqXdUDdu
MZyNDytRfGgRimBPSxyjuHtzrBWR8MyenjsbpraNoVDlFD8wVnGa5OcAv2gi7dkD
wloOSZj5jJq9WoMeGWEwp2TsQMySJDydBSTvgqovlk2K8gmeY69g2YUUmwR2Truf
fulBsO8upet/v2cRbCepI2X4NvS37wZBRcJtPpGcCoXUagA1vWH8eBKfjoduGERt
vc5c9DYjSA0VEJ3kzu3Atro/oNrZDDqvX1wEn+64fk1B8v53Lvf2X0ESQQUcfWpz
k7hPYzOt2IOA7d41CY59
=KMsn
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.3 pull request
This is the NFC pull request for 4.3.
With this one we have:
- A new driver for Samsung's S3FWRN5 NFC chipset. In order to
properly support this driver, a few NCI core routines needed
to be exported. Future drivers like Intel's Fields Peak will
benefit from this.
- SPI support as a physical transport for STM st21nfcb.
- An additional netlink API for sending replies back to userspace
from vendor commands.
- 2 small fixes for TI's trf7970a
- A few st-nci fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote checksum offload GRO did not consider the case that frag0
might be in use. This patch fixes that by accessing headers using the
skb_gro functions and not saving offsets relative to skb->head.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJV1FziAAoJEG4XJFUm622bEJwH/RdNlAK4+IS9Tx0K6EA2fDE3
001J16in/1IPPr8/RmQWNzHGN5/GAYlAdl5v4fkwb8qvcDCyPlQbSEC8ghd32H6M
G1101qEfGk9bhLTpI8xjeqsT1gl98LswPYNAfoRX4AJKAmNCkfJ1WILLi/Q2DUOf
oG6IersuqQOdQbkXDnMm49FBZeSkVvzsJL+WQhKhYblh0bDH3qGuLcYvtkSnt+P8
8QG5X+DPEpmaYcu+5E5N0XgffsdPj/+xXlFova4DFySDYb4OzEH1MYp/rHjPpnUo
nDJqxZIgkkmhu0CGtvpWNeSZ7GQBI0Bzdd+dwBY5yyg5AqWuQ5A1W+4r3SjvHyU=
=A8Ax
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all users are now converted to the inline implementation,
remove the out-of-line implementation entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper is required for irq chips which do not implement a
irq_set_type callback and need to call down the irq domain hierarchy
for the actual trigger type change.
This helper is required to fix further wreckage caused by the
conversion of TI OMAP to hierarchical irq domains and therefor tagged
for stable.
[ tglx: Massaged changelog ]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-3-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This switches the BCMA GPIO driver to use GPIOLIB_IRQCHIP to
handle its interrupts instead of rolling its own copy of the
irqdomain handling etc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJVzg5bAAoJEDBSmw7B7bqr3PAP/1r8wyZXxtySzz6P5Z9k0+2I
52NiSUISgmtnaQUyahf4n90eMU+gGJWQwPwIZFvMKg6bD4RW2XI4MdKmviKx8skU
4sDlDxMFrVMfV/ySwiPDAONWPtwwgKllIt0IDDnKs6kPdDlUcbKOTEFYhzZ1HhTZ
7Og4rJm7M90QpdMU7hmxmE5KRkp1hW0Yce1KPTW5U0j9yl9zbi4eLVWT+ac1WnZs
GpItajd0BFtBy7DRHzX8RiRJ4pi+aWxhuYNqiSxUm0BqPWCzT7PP15M1kCGwrXtm
/TTSVJl7WkLbOYI0PE0Y0XcJfZUg1c9aecCR3ubmRrQrGfOBFpN01jUANIRwqvZ3
3QRq1RZNLac0+zlBPjoFdOHmoaVX6UcJQKSgOhcfuM1BcNFnXZEcHFN4/SaEUfvJ
1ltybEeOEAckCMqqfHb1g/nVfJnlBjy811GzIrsHXqKqb7rRfGkfxmBxLrRzVknS
PC970pbuhxICeeryKdVgK5BClWeT3TB1srt6OZ0QR1zlcfZbLZ8jqJlHJcy3szFi
P43X9w8I6ZNTzkBU+lsCt9gbveYS+rSaJ+zm/SaF21ro33+FEdZ+p1ujjzp729Tz
PnKobaOrku38Be7CSwJ760WvngC7gbZqGybGknBsws4dqDXJste0UjxulZeyaOkN
nVmHDL45jc5rd8qjoPQV
=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' mac80211-next.git
iwlwifi needs new mac80211 patches so merge mac80211-next.git to
wireless-drivers-next.git.
Pull libata fixes from Tejun Heo:
"Three minor device-specific fixes and revert of NCQ autosense added
during this -rc1.
It turned out that NCQ autosense as currently implemented interferes
with the usual error handling behavior. It will be revisited in the
near future"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_brcmstb: Fix misuse of IS_ENABLED
sata_sx4: Check return code from pdc20621_i2c_read()
Revert "libata: Implement NCQ autosense"
Revert "libata: Implement support for sense data reporting"
Revert "libata-eh: Set 'information' field for autosense"
ata: ahci_brcmstb: Fix warnings with CONFIG_PM_SLEEP=n
kbuild test robot reported:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git master
head: d52736e24f
commit: 4e3c89920c [751/762] net: Introduce VRF related flags and helpers
reproduce: make htmldocs
>> Warning(include/linux/netdevice.h:1293): Enum value 'IFF_VRF_MASTER' not described in enum 'netdev_priv_flags'
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Eric noted netif_index_is_vrf is not called with rcu_read_lock held,
so wrap the dev_get_by_index_rcu in rcu_read_lock and unlock.
If VRF is not enabled or oif is 0 skip the device lookup. In both cases
index cannot be the VRF master.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only rx/tx pause settings.
Autoneg setting is currently not supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse builds have been warning for a really long time now
that etherdevice.h has a conversion that is unsafe.
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
This code change fixes the issue and generates the exact
same assembly before/after (checked on x86_64)
Fixes: 2c722fe1c8 (etherdevice: Optimize a few is_<foo>_ether_addr functions)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This private net_device flag can be set by drivers to inform that a
device runs fine without a qdisc attached. This was formerly done by
setting tx_queue_len to zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit was not according to ieee80211 specification.
Fix that.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having the EWMA parameters stored in the runtime struct imposes
memory requirements for the constant values that could just be
inlined in the code. This particularly makes sense if there are
a lot of such structs, for example in mac80211 in the station
table where each station has a number of these in an array, and
there can be many stations.
Provide a macro DECLARE_EWMA() that declares the necessary struct
and inline functions to access it with the parameters hard-coded;
using this also means the user no longer needs to 'select AVERAGE'
as it's entirely self-contained.
In the mac80211 case, on x86-64, this actually slightly *reduces*
code size, while also saving 80 bytes of runtime memory per sta.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a VRF_MASTER flag for interfaces and helper functions for determining
if a device is a VRF_MASTER.
Add link attribute for passing VRF_TABLE id.
Add vrf_ptr to netdevice.
Add various macros for determining if a device is a VRF device, the index
of the master VRF device and table associated with VRF device.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the ipv4 patch with a similar title, this adds a sysctl to allow
the user to change routing behavior based on whether or not the
interface associated with the nexthop was an up or down link. The
default setting preserves the current behavior, but anyone that enables
it will notice that nexthops on down interfaces will no longer be
selected:
net.ipv6.conf.all.ignore_routes_with_linkdown = 0
net.ipv6.conf.default.ignore_routes_with_linkdown = 0
net.ipv6.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, not only will link status be reported to
userspace, but an indication that a nexthop is dead and will not be used
is also reported.
1000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
1000::/8 via 8000::2 dev p8p1 metric 1024 pref medium
7000::/8 dev p7p1 proto kernel metric 256 dead linkdown pref medium
8000::/8 dev p8p1 proto kernel metric 256 pref medium
9000::/8 via 8000::2 dev p8p1 metric 2048 pref medium
9000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
fe80::/64 dev p7p1 proto kernel metric 256 dead linkdown pref medium
fe80::/64 dev p8p1 proto kernel metric 256 pref medium
This also adds devconf support and notification when sysctl values
change.
v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF has some helper functions for parsing MAC and PHY settings.
In cases where the platform is providing this information rather
than the device itself, there needs to be similar functions for ACPI.
These functions are slightly modified versions of the ones in
of_net which can use information provided via DT or ACPI.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Workaround hw bug when acquiring PCI bos ownership of iwlwifi
devices, from Emmanuel Grumbach.
2) Falling back to vmalloc in conntrack should not emit a warning, from
Pablo Neira Ayuso.
3) Fix NULL deref when rtlwifi driver is used as an AP, from Luis
Felipe Dominguez Vega.
4) Rocker doesn't free netdev on device removal, from Ido Schimmel.
5) UDP multicast early sock demux has route handling races, from Eric
Dumazet.
6) Fix L4 checksum handling in openvswitch, from Glenn Griffin.
7) Fix use-after-free in skb_set_peeked, from Herbert Xu.
8) Don't advertize NETIF_F_FRAGLIST in virtio_net driver, this can lead
to fraglists longer than the driver can support. From Jason Wang.
9) Fix mlx5 on non-4k-pagesize systems, from Carol L Soto.
10) Fix interrupt storm in bna driver, from Ivan Vecera.
11) Don't propagate -EBUSY from netlink_insert(), from Daniel Borkmann.
12) Fix inet request sock leak, from Eric Dumazet.
13) Fix TX interrupt masking and marking in TX descriptors of fs_enet
driver, from LEROY Christophe.
14) Get rid of rule optimizer in gianfar driver, it's buggy and unlikely
to get fixed any time soon. From Jakub Kicinski
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
cosa: missing error code on failure in probe()
gianfar: remove faulty filer optimizer
gianfar: correct list membership accounting
gianfar: correct filer table writing
bonding: Gratuitous ARP gets dropped when first slave added
net: dsa: Do not override PHY interface if already configured
net: fs_enet: mask interrupts for TX partial frames.
net: fs_enet: explicitly remove I flag on TX partial frames
inet: fix possible request socket leak
inet: fix races with reqsk timers
mkiss: Fix error handling in mkiss_open()
bnx2x: Free NVRAM lock at end of each page
bnx2x: Prevent null pointer dereference on SKB release
cxgb4: missing curly braces in t4_setup_debugfs()
net-timestamp: Update skb_complete_tx_timestamp comment
ipv6: don't reject link-local nexthop on other interface
netlink: make sure -EBUSY won't escape from netlink_insert
bna: fix interrupts storm caused by erroneous packets
net: mvpp2: replace TX coalescing interrupts with hrtimer
net: mvpp2: enable proper per-CPU TX buffers unmapping
...
After "62bccb8 net-timestamp: Make the clone operation stand-alone from phy
timestamping" the hwtstamps parameter of skb_complete_tx_timestamp() may no
longer be NULL.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the perf_event_map_fd and index, the function
bpf_perf_event_read() can convert the corresponding map
value to the pointer to struct perf_event and return the
Hardware PMU counter value.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new bpf map type 'BPF_MAP_TYPE_PERF_EVENT_ARRAY'.
This map only stores the pointer to struct perf_event. The
user space event FDs from perf_event_open() syscall are converted
to the pointer to struct perf_event and stored in map.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the map backends are of generic nature. In order to avoid
adding much special code into the eBPF core, rewrite part of
the bpf_prog_array map code and make it more generic. So the
new perf_event_array map type can reuse most of code with
bpf_prog_array map and add fewer lines of special code.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add three core perf APIs:
- perf_event_attrs(): export the struct perf_event_attr from struct
perf_event;
- perf_event_get(): get the struct perf_event from the given fd;
- perf_event_read_local(): read the events counters active on the
current CPU;
These APIs are needed when accessing events counters in eBPF programs.
The API perf_event_read_local() comes from Peter and I add the
corresponding SOB.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move the nfnl_acct_list into the network namespace, initialize
and destroy it per namespace
- Keep track of refcnt on nfacct objects, the old logic does not
longer work with a per namespace list
- Adjust xt_nfacct to pass the namespace when registring objects
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The pr_debug family of functions turns into a no-op when -DDEBUG is not
specified, opting instead to call "no_printk", which gets compiled to a
no-op (but retains gcc's nice warnings about printf-style arguments).
The problem with net_dbg_ratelimited is that it is defined to be a
variant of net_ratelimited_function, which expands to essentially:
if (net_ratelimit())
pr_debug(fmt, ...);
When DEBUG is not defined, then this becomes,
if (net_ratelimit())
;
This seems benign, except it isn't. Firstly, there's the obvious
overhead of calling net_ratelimit needlessly, which does quite some book
keeping for the rate limiting. Given that the pr_debug and
net_dbg_ratelimited family of functions are sprinkled liberally through
performance critical code, with developers assuming they'll be compiled
out to a no-op most of the time, we certainly do not want this needless
book keeping. Secondly, and most visibly, even though no debug message
is printed when DEBUG is not defined, if there is a flood of
invocations, dmesg winds up peppered with messages such as
"net_ratelimit: 320 callbacks suppressed". This is because our
aforementioned net_ratelimit() function actually prints this text in
some circumstances. It's especially odd to see this when there isn't any
other accompanying debug message.
So, in sum, it doesn't make sense to have this function's current
behavior, and instead it should match what every other debug family of
functions in the kernel does with !DEBUG -- nothing.
This patch replaces calls to net_dbg_ratelimited when !DEBUG with
no_printk, keeping with the idiom of all the other debug print helpers.
Also, though not strictly neccessary, it guards the call with an if (0)
so that all evaluation of any arguments are sure to be compiled out.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The race condition addressed in commit add05cecef ("mm: soft-offline:
don't free target page in successful page migration") was not closed
completely, because that can happen not only for soft-offline, but also
for hard-offline. Consider that a slab page is about to be freed into
buddy pool, and then an uncorrected memory error hits the page just
after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags &
PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not
necessary because the data on the affected page is not consumed.
To solve it, this patch drops __PG_HWPOISON from page flag checks at
allocation/free time. I think it's justified because __PG_HWPOISON
flags is defined to prevent the page from being reused, and setting it
outside the page's alloc-free cycle is a designed behavior (not a bug.)
For recent months, I was annoyed about BUG_ON when soft-offlined page
remains on lru cache list for a while, which is avoided by calling
put_page() instead of putback_lru_page() in page migration's success
path. This means that this patch reverts a major change from commit
add05cecef about the new refcounting rule of soft-offlined pages, so
"reuse window" revives. This will be closed by a subsequent patch.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen reported the following;
My laptop has been behaving strangely with 4.2-rc2. Once I log
in to my X session, I start getting all kinds of strange errors
from applications and see this in my dmesg:
VFS: file-max limit 8192 reached
The problem is that the file-max is calculated before memory is fully
initialised and miscalculates how much memory the kernel is using. This
patch recalculates file-max after deferred memory initialisation. Note
that using memory hotplug infrastructure would not have avoided this
problem as the value is not recalculated after memory hot-add.
4.1: files_stat.max_files = 6582781
4.2-rc2: files_stat.max_files = 8192
4.2-rc2 patched: files_stat.max_files = 6562467
Small differences with the patch applied and 4.1 but not enough to matter.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Dave Hansen <dave.hansen@intel.com>
Cc: Nicolai Stange <nicstange@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Alex Ng <alexng@microsoft.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
