Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.
There are
1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports
The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.
The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.
The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware interface required for port aggregation.
1. Disable RX port check on receive - don't perform a validity check
that matches to QP's port and the port where the packet is received.
2. Virtual to physical port remap - configure virtual to physical port
mapping. Port remap capability for virtual functions.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add event which provides an indication on a change in the state
of a bonding slave. The event handler should cast the pointer to the
appropriate type (struct netdev_bonding_info) in order to get the
full info about the slave.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds skb_remcsum_process and skb_gro_remcsum_process to
perform the appropriate adjustments to the skb when receiving
remote checksum offload.
Updated vxlan and gue to use these functions.
Tested: Ran TCP_RR and TCP_STREAM netperf for VXLAN and GUE, did
not see any change in performance.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical qdisc setup is the following :
bond0 : bonding device, using HTB hierarchy
eth1/eth2 : slaves, multiqueue NIC, using MQ + FQ qdisc
XPS allows to spread packets on specific tx queues, based on the cpu
doing the send.
Problem is that dequeues from bond0 qdisc can happen on random cpus,
due to the fact that qdisc_run() can dequeue a batch of packets.
CPUA -> queue packet P1 on bond0 qdisc, P1->ooo_okay=1
CPUA -> queue packet P2 on bond0 qdisc, P2->ooo_okay=0
CPUB -> dequeue packet P1 from bond0
enqueue packet on eth1/eth2
CPUC -> dequeue packet P2 from bond0
enqueue packet on eth1/eth2 using sk cache (ooo_okay is 0)
get_xps_queue() then might select wrong queue for P1, since current cpu
might be different than CPUA.
P2 might be sent on the old queue (stored in sk->sk_tx_queue_mapping),
if CPUC runs a bit faster (or CPUB spins a bit on qdisc lock)
Effect of this bug is TCP reorders, and more generally not optimal
TX queue placement. (A victim bulk flow can be migrated to the wrong TX
queue for a while)
To fix this, we have to record sender cpu number the first time
dev_queue_xmit() is called for one tx skb.
We can union napi_id (used on receive path) and sender_cpu,
granted we clear sender_cpu in skb_scrub_packet() (credit to Willem for
this union idea)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IPv6 cork initialization into its own function that
can be re-used. IPv6 specific cork data did not have an
explicit data structure. This patch creats eone so that
just ipv6 cork data can be as arguemts. Also, since
IPv6 tries to save the flow label into inet_cork_full
tructure, pass the full cork.
Adjust ip6_cork_release() to take cork data structures.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a high level feature flag for all switch asic offloads
switch drivers set this flag on switch ports. Logical devices like
bridge, bonds, vxlans can inherit this flag from their slaves/ports.
The patch also adds the flag to NETIF_F_ONE_FOR_ALL, so that it gets
propagated to the upperdevices (bridges and bonds).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.
The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SNWp
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 first pull request
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware spec states that the timeout for all commands should be 60 seconds.
In the past, the spec indicated that there were several classes of timeout
(short, medium, and long). The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.
In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
st21nfca has 1 physical SWP line and can support up to 2 secure elements
(UICC & eSE) thanks to an external switch managed with a gpio.
The platform integrator needs to specify thanks to 2 initialization
properties, uicc-present and ese-present, if it is suppose to have uicc
and/or ese. Of course if the platform does not have an external switch,
only one kind of secure element can be supported. Those parameters are
under platform integrator responsibilities.
During initialization, the white_list will be set according to those
parameters.
The discovery_se function will assume a secure element is physically
present according to uicc-present and ese-present values and will add it
to the secure element list. On ese activation, the atr is retrieved to
calculate a command exchange timeout based on the first atr(TB) value.
The se_io will allow to transfer data over SWP. 2 kind of events may appear
after a data is sent over:
- ST21NFCA_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCA_EVT_WTX_REQUEST when the secure element needs more time than
expected to compute a command. If this timeout expired, a first recovery
tentative consist to send a simple software reset proprietary command.
If this tentative still fail, a second recovery tentative consist to send
a hardware reset proprietary command.
This function is only relevant for eSE like secure element.
This patch also change the way a pipe is referenced. There can be
different pipe connected to the same gate with different host destination
(ex: CONNECTIVITY). In order to keep host information every pipe are
reference with a tuple (gate, host). In order to reduce changes, we are
keeping unchanged the way a gate is addressed on the Terminal Host.
However, this is working because we consider the apdu reader gate is only
present on the eSE slot also the connectivity gate cannot give a reliable
value; it will give the latest stored pipe value.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows mac80211 to configure BIP-CMAC-256 to the driver and also
use software-implementation within mac80211 when the driver does not
support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes cfg80211 aware of the GCMP, GCMP-256, CCMP-256, BIP-GMAC-128,
BIP-GMAC-256, and BIP-CMAC-256 cipher suites. These new cipher suites
were defined in IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to avoid double calls to phydev->drv->suspend and resume, keep
track of whether the PHY has already been suspended as a consequence of
a successful call to phy_suspend(). We will use this in our MDIO bus
suspend/resume hooks to avoid a double suspend call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
has_fixups was introduced to help keeping track of fixups/quirks running
on a PHY device, but we did not update the comment above struct
phy_device accordingly.
Fixes: b0ae009f3d (net: phy: add "has_fixups" boolean property")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"Six fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
drivers/rtc/rtc-s5m.c: terminate s5m_rtc_id array with empty element
printk: add dummy routine for when CONFIG_PRINTK=n
mm/vmscan: fix highidx argument type
memcg: remove extra newlines from memcg oom kill log
x86, build: replace Perl script with Shell script
mm: page_alloc: embed OOM killing naturally into allocation slowpath
Kalle Valo says:
====================
pull-request: wireless-drivers-next 2015-01-22
now a bigger pull request for net-next. Rafal found a UTF-8 bug in
patchwork[1] and because of that two commits (d0c102f70a and
d0f66df539) have his name corrupted:
Acked-by: Rafa? Mi?ecki <zajec5@gmail.com>
Somehow I failed to spot that when I commited the patches. As rebasing
public git trees is bad, I thought we can live with these and decided
not to rebase. But I'll pay close attention to this in the future to
make sure that it won't happen again. Also we requested an update to
patchwork.kernel.org, the latest patchwork doesn't seem to have this
bug.
Also please note this pull request also adds one DT binding doc, but
this was reviewed in the device tree list:
.../bindings/net/wireless/qcom,ath10k.txt | 30 +
Please let me know if you have any issues.
[1] https://lists.ozlabs.org/pipermail/patchwork/2015-January/001261.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One correctness fix here for the s2mps11 driver which would have
resulted in some of the regulators being completely broken together with
a fix for locking in regualtor_put() (which is fortunately rarely called
at all in practical systems).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUxiDBAAoJECTWi3JdVIfQNgYH/0ziCp+Hgxqi6qbCwJSMtzHN
m0kei13bC9gCNH6SM7iYg1XoYN+qduYU8JdUHflvpxHmsOOt3PgUsVfAFPkX2xeA
i9z0mZV47XOnX9eQQ+LweW4qLykhp/mbOxqDwyCix/PqKvPKChE7aJzAMCIn5kUl
GgBcU2pBFTIDNXxibzuuEtfRUho+ry4w1JARI2r0n9Q5FQULPxOBhtP0RQlGZyW9
+7tL/PBG4XYWUqOsg0wVHi5TA5kzrehPeW9GJhUIIdV7vcv9ACU6/T+aK9O6vqcv
IeDM+NfIkHT81eXc8a+Zm6ud8TV585n7s8gQtqrAy25BTlBBfcGeqX3hOjZhAzU=
=GLc6
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One correctness fix here for the s2mps11 driver which would have
resulted in some of the regulators being completely broken together
with a fix for locking in regualtor_put() (which is fortunately rarely
called at all in practical systems)"
* tag 'regulator-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix wrong calculation of register offset
regulator: core: fix race condition in regulator_put()
include/linux/platform_data/st21nfcb.h is based on
include/linux/platform_data/st21nfca.h.
The endif comment is inacurrate for st21nfcb.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
include/linux/platform_data/st21nfcb.h is phy generic.
There is no need to include linux/i2c.h
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are missing dummy routines for log_buf_addr_get() and
log_buf_len_get() for when CONFIG_PRINTK is not set causing build
failures.
This patch adds these dummy routines at the appropriate location.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OOM killing invocation does a lot of duplicative checks against the
task's allocation context. Rework it to take advantage of the existing
checks in the allocator slowpath.
The OOM killer is invoked when the allocator is unable to reclaim any
pages but the allocation has to keep looping. Instead of having a check
for __GFP_NORETRY hidden in oom_gfp_allowed(), just move the OOM
invocation to the true branch of should_alloc_retry(). The __GFP_FS
check from oom_gfp_allowed() can then be moved into the OOM avoidance
branch in __alloc_pages_may_oom(), along with the PF_DUMPCORE test.
__alloc_pages_may_oom() can then signal to the caller whether the OOM
killer was invoked, instead of requiring it to duplicate the order and
high_zoneidx checks to guess this when deciding whether to continue.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"next" is not updated, causing an endless loop for buckets with more than
one element.
Fixes: 88d6ed15ac ("rhashtable: Convert bucket iterators to take table and index")
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- regression fix for exynos_mct clocksource
- trivial build fix for kona clocksource
- functional one liner fix for the sh_tmu clocksource
- two validation fixes to prevent (root only) data corruption in the
kernel via settimeofday and adjtimex. Tagged for stable"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: adjtimex: Validate the ADJ_FREQUENCY values
time: settimeofday: Validate the values of tv from user
clocksource: sh_tmu: Set cpu_possible_mask to fix SMP broadcast
clocksource: kona: fix __iomem annotation
clocksource: exynos_mct: Fix bitmask regression for exynos4_mct_write
The kernel forcefully applies MTU values received in router
advertisements provided the new MTU is less than the current. This
behavior is undesirable when the user space is managing the MTU. Instead
a sysctl flag 'accept_ra_mtu' is introduced such that the user space
can control whether or not RA provided MTU updates should be applied. The
default behavior is unchanged; user space must explicitly set this flag
to 0 for RA MTUs to be ignored.
Signed-off-by: Harout Hedeshian <harouth@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning. When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.
The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.
The VF shall reset itself in the following cases:
1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.
2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.
Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.
As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
commands to the PF and getting timed-out.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.
Implement the remove_one case, handling AER and other cases comes next.
The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.
The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.
In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.
The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.
Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes:
- resetting the chip when a fatal error is detected (the current code
does not do this).
- exposing the ability to enter error state from outside the catas code
by calling its functionality. (E.g. FW Command timeout, AER error).
- managing a persistent device state. This is needed to sync between
reset flow cases.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a WQ per device instead of a single global WQ, this allows
independent reset handling per device even when SRIOV is used.
This comes as a pre-patch for supporting chip reset
for both native and SRIOV.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an HCA enters an internal error state, this is detected by the driver.
The driver then should reset the HCA and restart the software stack.
Keep ports information and some SRIOV configuration in a persistent area
to have it valid across reset.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource management
- Clip bridge windows to fit in upstream windows (Yinghai Lu)
Virtualization
- Mark Atheros AR93xx to avoid using bus reset (Alex Williamson)
Miscellaneous
- Update Richard Zhu's email address (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HRy7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for:
- a resource management problem that causes a Radeon "Fatal error
during GPU init" on machines where the BIOS programmed an invalid
Root Port window. This was a regression in v3.16.
- an Atheros AR93xx device that doesn't handle PCI bus resets
correctly. This was a regression in v3.14.
- an out-of-date email address"
* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Richard Zhu's email address
sparc/PCI: Clip bridge windows to fit in upstream windows
powerpc/PCI: Clip bridge windows to fit in upstream windows
parisc/PCI: Clip bridge windows to fit in upstream windows
mn10300/PCI: Clip bridge windows to fit in upstream windows
microblaze/PCI: Clip bridge windows to fit in upstream windows
ia64/PCI: Clip bridge windows to fit in upstream windows
frv/PCI: Clip bridge windows to fit in upstream windows
alpha/PCI: Clip bridge windows to fit in upstream windows
x86/PCI: Clip bridge windows to fit in upstream windows
PCI: Add pci_claim_bridge_resource() to clip window if necessary
PCI: Add pci_bus_clip_resource() to clip to fit upstream window
PCI: Pass bridge device, not bus, when updating bridge windows
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done
a bit later, with memory allocator available. This allows us to simplify
code by using standard bus scanning method.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First two are minor fallout from the param rework which went in this merge
window.
Next three are a series which fixes a longstanding (but never previously
reported and unlikely , so no CC stable) race between kallsyms and freeing
the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kf9b
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module and param fixes from Rusty Russell:
"Surprising number of fixes this merge window :(
The first two are minor fallout from the param rework which went in
this merge window.
The next three are a series which fixes a longstanding (but never
previously reported and unlikely , so no CC stable) race between
kallsyms and freeing the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: make module_refcount() a signed integer.
module: fix race in kallsyms resolution during module load success.
module: remove mod arg from module_free, rename module_memfree().
module_arch_freeing_init(): new hook for archs before module->module_init freed.
param: fix uninitialized read with CONFIG_DEBUG_LOCK_ALLOC
param: initialize store function to NULL if not available.
James Bottomley points out that it will be -1 during unload. It's
only used for diagnostics, so let's not hide that as it could be a
clue as to what's gone wrong.
Cc: Jason Wessel <jason.wessel@windriver.com>
Acked-and-documention-added-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Masami Hiramatsu <maasami.hiramatsu.pt@hitachi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull libata fixes from Tejun Heo:
- Bartlomiej will be co-maintaining PATA portion of libata. git
workflow will stay the same.
- sata_sil24 wasn't happy with tag ordered submission. An option to
restore the old tag allocation behavior is implemented for sil24.
- a very old race condition in PIO host state machine which can trigger
BUG fixed.
- other driver-specific changes
* 'for-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: prevent HSM state change race between ISR and PIO
libata: allow sata_sil24 to opt-out of tag ordered submission
ata: pata_at91: depend on !ARCH_MULTIPLATFORM
ahci: Remove Device ID for Intel Sunrise Point PCH
ahci: Use dev_info() to inform about the lack of Device Sleep support
libata: Whitelist SSDs that are known to properly return zeroes after TRIM
sata_dwc_460ex: fix resource leak on error path
ata: add MAINTAINERS entry for libata PATA drivers
libata: clean up MAINTAINERS entries
libata: export ata_get_cmd_descript()
ahci_xgene: Fix the DMA state machine lockup for the ATA_CMD_PACKET PIO mode command.
ahci_xgene: Fix the endianess issue in APM X-Gene SoC AHCI SATA controller driver.
Pull networking fixes from David Miller:
1) Socket addresses returned in the error queue need to be fully
initialized before being passed on to userspace, fix from Willem de
Bruijn.
2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren.
3) Fix races between receive packet steering and cpu hotplug, from Eric
Dumazet.
4) Allowing netlink sockets to subscribe to unknown multicast groups
leads to crashes, don't allow it. From Johannes Berg.
5) One to many socket races in SCTP fixed by Daniel Borkmann.
6) Put in a guard against the mis-use of ipv6 atomic fragments, from
Hagen Paul Pfeifer.
7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben
Hutchings.
8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and
Byungho An.
9) cfg80211 deadlock fix from Arik Nemtsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
s2io: use snprintf() as a safety feature
r8152: remove sram_read
r8152: remove generic_ocp_read before writing
bgmac: activate irqs only if there is nothing to poll
bgmac: register napi before the device
sh_eth: Fix ethtool operation crash when net device is down
sh_eth: Fix promiscuous mode on chips without TSU
ipv6: stop sending PTB packets for MTU < 1280
net: sctp: fix race for one-to-many sockets in sendmsg's auto associate
genetlink: synchronize socket closing and family removal
genetlink: disallow subscribing to unknown mcast groups
genetlink: document parallel_ops
net: rps: fix cpu unplug
net: davinci_emac: Add support for emac on dm816x
net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space
net: davinci_emac: Fix incomplete code for getting the phy from device tree
net: davinci_emac: Free clock after checking the frequency
net: davinci_emac: Fix runtime pm calls for davinci_emac
net: davinci_emac: Fix hangs with interrupts
ip: zero sockaddr returned on error queue
...
Nothing needs the module pointer any more, and the next patch will
call it from RCU, where the module itself might no longer exist.
Removing the arg is the safest approach.
This just codifies the use of the module_alloc/module_free pattern
which ftrace and bpf use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: x86@kernel.org
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: netdev@vger.kernel.org
Archs have been abusing module_free() to clean up their arch-specific
allocations. Since module_free() is also (ab)used by BPF and trace code,
let's keep it to simple allocations, and provide a hook called before
that.
This means that avr32, ia64, parisc and s390 no longer need to implement
their own module_free() at all. avr32 doesn't need module_finalize()
either.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101
"Since commit 8a4aeec8d "libata/ahci: accommodate tag ordered
controllers" the access to the harddisk on the first SATA-port is
failing on its first access. The access to the harddisk on the
second port is working normal.
When reverting the above commit, access to both harddisks is working
fine again."
Maintain tag ordered submission as the default, but allow sata_sil24 to
continue with the old behavior.
Cc: <stable@vger.kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Reported-by: Ronny Hegewald <Ronny.Hegewald@online.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch benefits from newly introduced switchdev notifier and uses it
to propagate fdb learn events from rocker driver to bridge. That avoids
direct function calls and possible use by other listeners (ovs).
Suggested-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the problem Jeff Layton reported, I looked at the code
and reproduced the same warning by subscribing and removing the genl
family with a socket still open. This is a fairly tricky race which
originates in the fact that generic netlink allows the family to go
away while sockets are still open - unlike regular netlink which has
a module refcount for every open socket so in general this cannot be
triggered.
Trying to resolve this issue by the obvious locking isn't possible as
it will result in deadlocks between unregistration and group unbind
notification (which incidentally lockdep doesn't find due to the home
grown locking in the netlink table.)
To really resolve this, introduce a "closing socket" reference counter
(for generic netlink only, as it's the only affected family) in the
core netlink code and use that in generic netlink to wait for all the
sockets that are being closed at the same time as a generic netlink
family is removed.
This fixes the race that when a socket is closed, it will should call
the unbind, but if the family is removed at the same time the unbind
will not find it, leading to the warning. The real problem though is
that in this case the unbind could actually find a new family that is
registered to have a multicast group with the same ID, and call its
mcast_unbind() leading to confusing.
Also remove the warning since it would still trigger, but is now no
longer a problem.
This also moves the code in af_netlink.c to before unreferencing the
module to avoid having the same problem in the normal non-genl case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlS5WTQACgkQMUfUDdst+ykYQgCffWxrhuQKYJLYVYmIoDS8lL/c
1v4AoIowfSV08l22puWQpAOih/tg0WGI
=mfZA
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems"
* tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
usb: dwc3: gadget: Stop TRB preparation after limit is reached
usb: dwc3: gadget: Fix TRB preparation during SG
usb: phy: mv-usb: fix usb_phy build errors
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
usb: serial: silence all non-critical read errors
USB: console: fix potential use after free
USB: console: fix uninitialised ldisc semaphore
usb: gadget: udc: atmel: fix possible oops when unloading module
usb: gadget: gadgetfs: fix an oops in ep_write()
usb: phy: Fix deferred probing
OHCI: add a quirk for ULi M5237 blocking on reset
uas: Add US_FL_NO_ATA_1X for 2 more Seagate disk enclosures
uas: Do not blacklist ASM1153 disk enclosures
usb: gadget: udc: avoid dereference before NULL check in ep_queue
usb: host: ehci-tegra: request deferred probe when failing to get phy
uas: disable UAS on Apricorn SATA dongles
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS566 with usb-id 0bc2:a013
uas: Add US_FL_NO_ATA_1X for Seagate devices with usb-id 0bc2:a013
xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
USB: EHCI: adjust error return code
...
Highlights include:
- Stable fix for a NFSv3/lockd race
- Fixes for several NFSv4.1 client id trunking bugs
- Remove an incorrect test when checking for delegated opens
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hz4r
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Stable fix for a NFSv3/lockd race
- Fixes for several NFSv4.1 client id trunking bugs
- Remove an incorrect test when checking for delegated opens"
* tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Remove incorrect check in can_open_delegated()
NFS: Ignore transport protocol when detecting server trunking
NFSv4/v4.1: Verify the client owner id during trunking detection
NFSv4: Cache the NFSv4/v4.1 client owner_id in the struct nfs_client
NFSv4.1: Fix client id trunking on Linux
LOCKD: Fix a race when initialising nlmsvc_timeout
