mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm,
but not good practice.
Reported by the Mellanox Beijing team.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit
architectures.
This commit makes that padding explicit, to prevent issues with
changing compilers and with incompatibilities between 32-bit architecture
implicit padding and 64-bit architecture implicit padding.
This structure is used in virtualization for communication between
the Host and its Guests. The explicit padding allows 64-bit Hosts
(old and new) to continue to interoperate with 64-bit Guests (old and new).
However, without this fix, 64-bit Hosts could not interoperate with 32-bit
Guests (since these did not insert the padding dword). With this fix,
32-bit Guests will be able to interoperate with 64-bit Hosts (since
the structure offsets will be identical on both).
Reported-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware spec states that the timeout for all commands should be 60 seconds.
In the past, the spec indicated that there were several classes of timeout
(short, medium, and long). The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.
In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structs allocated for the resource tracker must be freed in
the error flow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.
The reserved L_key value for a VF is:
VF_lkey = base_lkey + (VF_number << 8).
This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.
To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.
When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit is based on a wrong assumption, fdb messages are always sent
into the netns where the interface stands (see vxlan_fdb_notify()).
These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we
need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example).
Note also that vxlan_nlmsg_size() was not updated.
Fixes: 193523bf93 ("vxlan: advertise netns of vxlan dev in fdb msg")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Toppins says:
====================
bonding: various 802.3ad fixes
This patch series is a forward porting of patches we (Cumulus) are shipping
in our 3.2 series kernels. These fixes attempt to make 802.3ad bonding mode
more predictable in certian state machine transtions in addition to fixing
802.3ad bond carrier determination when bonding min_links option is changed.
Specific notes are contained within each patch.
For this patch series there are no userspace facing changes, a diff between
the modinfo output showed no difference. However, there are behavioral
facing changes, primarily in the bond carrier state. Please make sure to
review carefully.
v2:
* fixed some style issues
* dropped a portion of patch 1 in favor of more testing on my side
====================
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix sparse warning about non-static function
drivers/net/bonding/bond_main.c:3737:5: warning: symbol
'bond_3ad_xor_xmit' was not declared. Should it be static?
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a slave is added to a bond and it is not in full duplex mode,
AD_PORT_LACP_ENABLED flag is cleared, due to this LACP PDU is not sent
on slave. When the duplex is changed to full, the flag needs to be set
to send LACP PDU.
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to fix the following problems when an actor or
partner's aggregator is not active:
1. a slave's lacp port state is marked as AD_STATE_SYNCHRONIZATION
even if it is attached to an inactive aggregator. LACP advertises
this state to the partner, making the partner think he can move
into COLLECTING_DISTRIBUTING state even though this link will not
pass traffic on the local side
2. a slave goes into COLLECTING_DISTRIBUTING state without checking
if the aggregator is actually active
3. when in COLLECTING_DISTRIBUTING state, the partner parameters may
change, e.g. the partner_oper_port_state.SYNCHRONIZATION. The
local mux machine is not reacting to the change and continue to
keep the slave and bond up
4. When bond slave leaves an inactive aggregator and joins an active
aggregator, the actor oper port state need to update to SYNC state.
v2:
* fix style issues in bond_3ad.c
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode 802.3ad, fix incorrect bond slave active state when slave is not in
active aggregator. During bond_open(), the bonding driver always sets
the slave active flag to true if the bond is not in active-backup, alb,
or tlb modes. Bonding should let the aggregator selection logic set the
active flag when in 802.3ad mode.
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move pxa25x clock drivers from arch/arm/mach-pxa to driver/clk.
In the move :
- convert to new clock framework legacy clocks
- provide clocks as before for platform data based boards
- provide clocks through devicetree with clk-pxa-dt
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The CPU_2X clock does not have a classical in-kernel user, but is,
amongst other things, required for OCM and debug access. Make sure this
clock is not mistakenly disabled during boot up by enabling it in the
platform's clock driver.
Cc: stable@vger.kernel.org # 3.11+
Fixes: 0ee52b157b 'clk: zynq: Add clock controller driver'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch just fixes up the declarations.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The set of clock changes for the 3.20 merge window, with mostly:
- Some PLL fixes for the A80 and A31
- The MMC custom phase functions are removed, and moved over to the generic
phase API.
- Add the A80 MMC clocks
Some DT changes slipped here as well, to preserve bisectability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m8K6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner clock changes for 3.20
The set of clock changes for the 3.20 merge window, with mostly:
- Some PLL fixes for the A80 and A31
- The MMC custom phase functions are removed, and moved over to the generic
phase API.
- Add the A80 MMC clocks
Some DT changes slipped here as well, to preserve bisectability.
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUwT2NAAoJEPOmecmc0R2BjmsH/1Mp2vS9E9RBREhL/uuwtVlE
6FhINcpzVkDrwXGfupVbrWmzHTxKcyUbnluVPsLs0BCRqhhKSU0t+TT5j+mRMOpu
oNq/d3cp//fuBaiLr4G0jrgd/a9Gq4SsshPP6kH41r5CBN87jTt9wazX2GjNBf4C
LYsNNWj/qpXxeA/rFuMsI15ntPiFvap8Ag/5+IDCHuT9nwCLy7iI3G0MRGZ1kfGT
byOJd/FOqfAk3UJXuEgGOu27ZAOcbGLk7EL7YUdq7C70wAlUTu/8smTLqJFbXc9T
Xgum3FnYcuPZqNQSxQMXFpgyzE0q7KLyufv5gU1A4s2Ac69cD3nDVh9k1LAcu4s=
=arKA
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
The two big changes are the additional of the watchdog clock, which
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUyCaJAAoJEPOmecmc0R2By0oH/ioVbVZWYgTWJRlN0Cmjj+yr
fNnzm93g9N+Uk5PGOjCw70h3QSS65OLdqPF9xJwkSS1p7ORbKmOU3fzAET7x/EYK
a3Ct4NRPPiSkY12Qg+N4Q9wjz8sgUUHsLSFa5D/QJsyPu+lTVhLgWS4j4mzVCbyz
PSMn4Tx52OHzLHWKGrnEq33AIMROvarBmOgnvGe7AbutwDYqoiFiPALIAowrp/SR
WY689+3Gjtha5epUHn9vgUkNABnf0gXR1MBBJ1ZMxgForjZqeSCioHNYomneKOZC
9zyg4yuv5kNL75PY4aHLwalRfIFrqNM5S5D3gH7CTQg1/TcfUcVCBY0CAKczLxw=
=nDW6
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: second batch of dts updates for 3.20" from Heiko Stübner:
Basic display nodes for crtcs and hdmi encoder, timer node
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
* tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
dt-bindings: add vendor prefix and root compatible property for Rockchip boards
ARM: dts: rockchip: Add rockchip timer node for rk3288
ARM: dts: rockchip: add rk3288 hdmi nodes
ARM: dts: rockchip: Add rk3288 vop and display-subsystem
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently there is no support for ACPI.
This patch uses the following configuration:
- Device id: NXP5440
- Pin mapping:
- 0 IRQ pin
- 1 enable pin
- 2 firmware pin
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The biggest part of these changes is the conversion to atomic mode-
setting. A lot of cleanup and demidlayering was required before the
conversion, with the result being a whole lot of changes.
Besides the atomic mode-setting support, the host1x bus now has the
proper infrastructure to support suspend/resume for child devices.
Finally, a couple of smaller cleanup patches round things off.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUx1hgAAoJEN0jrNd/PrOhpOIQAI7YAJUX7465R59vkjXOV3uP
lGMj75v22Wq2Y3poPNyxnn562W0feKVBPf13oWgZvzK1fk3+eXoVmL2F395VYXjz
rsGhJJe+/z8gtBgNXH0l6jzvQwRHzLCoMpt9Egrzbij6S+BShQZvnwg5Gyws6vBe
ZnpTjxJKZD4ADY5G1J/EFmBAW3B3abZqOLGHohbUSeN/rr3VP92eG7vnPDW8Rrry
UuBJkjdkR49cfnEvz4pCEoiucftIja7y0YhkDy6estPnO3JBDQ01tCI6HvA6CT1k
6wCkWOnPXJ1Uy1OcXgMU59azJ7d8wdwXFWCXc5yWwIj47ZmY6OjwyJfURmrlQ6nb
8lxeedCBgmTLF6sB9g8g117HWCM3InUXOeN4EhkcF6el9X+ZOAlIJO2RllfL8Bwn
O0GXgCmeeeoZG6aLpULEnAZhJZ92nvo2Zn5lddk7uiaU09Xdzc4kKN3FzYS0XtfJ
7A32m/DNPQi9yJnFFK2sWrrSBnHcDd0Cq17/V1VTcP6iV3CtRWIDX7co0QHE+EQl
7xjj2rlFEyWcvD+9pUoYEgDDCuzjy41zCQ53vj+h2xDO6maksqT1vJ1Nz8y9JmQI
F52aU+DyHleP3q0u9CmeFIo1ft5ho7IgzPJXHPqir/QcnxqiqDprEM70bQwVdF+y
iVvngQ3xfkH2RaqOwen0
=k0/3
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.20-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.20-rc1
The biggest part of these changes is the conversion to atomic mode-
setting. A lot of cleanup and demidlayering was required before the
conversion, with the result being a whole lot of changes.
Besides the atomic mode-setting support, the host1x bus now has the
proper infrastructure to support suspend/resume for child devices.
Finally, a couple of smaller cleanup patches round things off.
* tag 'drm/tegra/for-3.20-rc1' of git://anongit.freedesktop.org/tegra/linux: (54 commits)
drm/tegra: Use correct relocation target offsets
drm/tegra: Add minimal power management
drm/tegra: dc: Unify enabling the display controller
drm/tegra: Track tiling and format in plane state
drm/tegra: Track active planes in CRTC state
drm/tegra: Remove unused ->mode_fixup() callbacks
drm/tegra: Atomic conversion, phase 3, step 3
drm/tegra: Atomic conversion, phase 3, step 2
drm/tegra: dc: Use atomic clock state in modeset
drm/tegra: sor: Implement ->atomic_check()
drm/tegra: hdmi: Implement ->atomic_check()
drm/tegra: dsi: Implement ->atomic_check()
drm/tegra: rgb: Implement ->atomic_check()
drm/tegra: dc: Store clock setup in atomic state
drm/tegra: Atomic conversion, phase 3, step 1
drm/tegra: Atomic conversion, phase 2
drm/tegra: Atomic conversion, phase 1
drm/tegra: dc: Do not needlessly deassert reset
drm/tegra: Output cleanup functions cannot fail
drm/tegra: Remove remnants of the output midlayer
...
The xfstests btrfs/072 reports uncorrectable read errors in dmesg,
because scrub forgets to use commit_root for parity scrub routine
and scrub attempts to scrub those extents items whose contents are
not fully on disk.
To fix it, we just add the @search_commit_root flag back.
Signed-off-by: Gui Hecheng <guihc.fnst@cn.fujitsu.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Chris Mason <clm@fb.com>
gpio_set_value was replaced with gpio_set_value_cansleep in order
to allow GPIO access that may sleep. This is particularelly useful
when GPIO is accessed using busses like I2C, SPI, USB
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the USART peripheral as UART for low level debug. Only the UA0 port is
currently supported.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for FSL's LS2085A SoC in the arm64 Kconfig
and defconfig files.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnab Basu <arnab_basu@rocketmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the device tree support for FSL LS2085A SoC
based on ARMv8 architecture.
Following levels of DTSI/DTS files have been created for the
LS2085A SoC family:
- fsl-ls2085a.dtsi:
DTS-Include file for FSL LS2085A SoC.
- fsl-ls2085a-simu.dts:
DTS file for FSL LS2085a software simulator model.
In addition, this patch adds build support for FSL's LS2085A
simulator model in arm64 dts Makefile.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnab Basu <arnab_basu@rocketmail.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds a devicetree binding documentation for FSL's
Management Complex.
Management Complex is a hardware resource manager that manages
specialized hardware objects used in network-oriented packet
processing applications
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds a devicetree binding documentation for FSL's
LS2085A SoC and Simulator model.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch addss the device-tree documentation for Freescale's
NS16550 UART (also called DUART).
There is a specific errata fix required in FSL NS16550 UART
which ensures that an random interrupt storm is not observed when
a break is provided as an input to the UART.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On st21nfca, the mechanism to enable a secure element needs to add 2
properties in order manage the SWP line correctly.
Document ese-present and uicc-present properties.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfca has 1 physical SWP line and can support up to 2 secure elements
(UICC & eSE) thanks to an external switch managed with a gpio.
The platform integrator needs to specify thanks to 2 initialization
properties, uicc-present and ese-present, if it is suppose to have uicc
and/or ese. Of course if the platform does not have an external switch,
only one kind of secure element can be supported. Those parameters are
under platform integrator responsibilities.
During initialization, the white_list will be set according to those
parameters.
The discovery_se function will assume a secure element is physically
present according to uicc-present and ese-present values and will add it
to the secure element list. On ese activation, the atr is retrieved to
calculate a command exchange timeout based on the first atr(TB) value.
The se_io will allow to transfer data over SWP. 2 kind of events may appear
after a data is sent over:
- ST21NFCA_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCA_EVT_WTX_REQUEST when the secure element needs more time than
expected to compute a command. If this timeout expired, a first recovery
tentative consist to send a simple software reset proprietary command.
If this tentative still fail, a second recovery tentative consist to send
a hardware reset proprietary command.
This function is only relevant for eSE like secure element.
This patch also change the way a pipe is referenced. There can be
different pipe connected to the same gate with different host destination
(ex: CONNECTIVITY). In order to keep host information every pipe are
reference with a tuple (gate, host). In order to reduce changes, we are
keeping unchanged the way a gate is addressed on the Terminal Host.
However, this is working because we consider the apdu reader gate is only
present on the eSE slot also the connectivity gate cannot give a reliable
value; it will give the latest stored pipe value.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the newly introduced pipes table hci_dev fields,
the nfc_hci_pipe2gate routine is no longer needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a command is received, it is sometime needed to let the CLF driver do
some additional operations. (ex: count remaining pipe notification...)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We update the tracked pipes status when receiving HCI commands.
Also we forward HCI errors and we reply to any HCI command, even though
we don't support it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Of the Digicolor SoCs series only CX92755 is currently supported.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial support for the Conexant CX92755 SoC. The CX92755 is one of the
Digicolor series of SoCs, all sharing many of the same peripherals. The code
was tested on the CX92755 evaluation kit, AKA Equinox.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
As there can be several pipes connected to the same gate, we need
to know which pipe ID to use when sending an HCI response. A gate
ID is not enough.
Instead of changing the nfc_hci_send_response() API to something
not aligned with the rest of the HCI API, we call nfc_hci_hcp_message_tx
directly.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit "ARM: pxa: arbitrarily set first interrupt number" broke viper
and zeus boards which still refer to PXA_ISA_IRQ() macro. Redefine
the macro, which declares the legacy interrupts from 0 to 15.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove the output-confusing newline below:
[ 0.191328]
**********************************************************
[ 0.191493] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.191586] ** **
...
Link: http://lkml.kernel.org/r/1422375440-31970-1-git-send-email-bp@alien8.de
Signed-off-by: Borislav Petkov <bp@suse.de>
[ added an extra '\n' by itself, to keep what it was suppose to do ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When ktest runs the console program as a child process, the parent and
child share the same tty for stdin and stderr. This is problematic when
using a libvirt target. The "virsh console" program makes a lot of
changes to the tty settings, making ktest's output hard to read
(carriage returns don't work). After ktest exits, the terminal is
unusable (CRs broken, stdin isn't echoed).
I think the best way to fix this issue would be to create a
pseudoterminal (pty pair) so the child process would have a dedicated
tty, and then use pipes to connect the two ttys. I'm not sure if that's
overkill, but it's far beyond my current Perl abilities.
This patch is a much easier way to (partially) fix this issue. It saves
the tty settings before opening the console and restores them after
closing it. There are still a few places where ktest prints mangled
output while the console is open, but the output is much more legible
overall, and the terminal works just fine after ktest exits.
Link: http://lkml.kernel.org/r/1bb89abc0025cf1d6da657c7ba58bbeb4381a515.1422382008.git.jpoimboe@redhat.com
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I find that I usually like to see how long a make or other command takes,
and adding a start and end time and reporting how long each command runs
(in seconds) is helpful.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
