SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:
drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here
Fixes: 3a939a6712 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In AP mode, beacon frame is necessary to keep connection.
this patch adds a sending beacon frame routine in initialization routine.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds fix to set carrier state off during ndo_open.
Carrier should be set to ON when device is ready to send data.
In case of station/adhoc interface device is able to transfer
data after successful association/join operation.
For AP this would be after bss_active event.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the clock can be get from TK/RK pin, so remove the comments.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the I2S specification information as following:
- WS = 0, channel 1 (left)
- WS = 1, channel 2 (right)
So, the start event should be TF/RF falling edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The number of words in the read buffer will be exactly the same as the
number of words written on write buffer, once the transaction has
finished.
Instead of cheking the rx_empty flags for every word simply save the
number of words written by fill_tx_fifo.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add description for the driver
- Add dependency on the I2C module
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
make the sta32x driver usable with device tree configs. Code is heavily based
on the sta350 driver.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reset GPIO on the STA32X Codecs is used to reset the Codec and clear
all registers. Also taking it down puts the IC in power save mode, so
we put the device in reset mode when we go to sleep.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use the regmap API directly rather than relying on the snd_soc_read/write
functions as this seems to be in accordance with common practice.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IDE bit in the CONFF register is the third bit not the fourth.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
unloading: this broke with new atomic refcounting. The code is still
suspicious, but this solves the WARN_ON().
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUxuOxAAoJENkgDmzRrbjxtGIP/im0s3L+wM28NdQ5zFOiIpwX
0N4y4U6Aa+rrLs27jDZtXW4ss+fr/V7pUSD1uwTrTHl9X4a3M+DLpEME5Rq40TXG
MYHihlQo8PM/yCuTMFR7esF20/q9CIksuVA3GkjYqwBW+ks097+t60Yn7YSfX22U
HzSiR3Pp6yPjMoZWROP576rc9VtOM6tScKU1rzwe8Bo7ayzNADmTFJR4UpQuiQhU
NwHn7Lih6EGsVTtaX3KS91dA7v5Un/S4jskqAkkwOW3ipgf38LLfjETueHvDWpda
szVFoMMMkqDwse2MyluiLk/80Cpl528GO24D0MMbQoPfsUi7OgxQN6t1QviRxeut
pH1VyK4VrRDqhpGB+5l7PQUOk58dL4SjmIVO/G9wxMgKzw2giONJdt/zHBXMr5/l
6RYINwHEQalMoG3X+kgYKa5E1WPXeJsE4xQTBIQRsaHO+9lk95BbNUVfUgvygUPV
TTaymhHhEYOsntiMHPkTI05FkK79khs/qX7lU1MVtZ9x7UaYXs3ziY7z+D5fRKf1
WgoYemWBeFZznsceacNSZGjFsaMJr6gsZ/rVuPSbytXDXSOrQsJxiENph7CnHbRk
4UJffEomjdQ93CNGBI2hCYlr4Gf5DflbwHjJbT+YXcqumkXJq4+ktSFp5aCH+9q8
901XYQ7QIJ4roIOzODUG
=JI7o
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull one more module fix from Rusty Russell:
"SCSI was using module_refcount() to figure out when the module was
unloading: this broke with new atomic refcounting. The code is still
suspicious, but this solves the WARN_ON()"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
scsi: always increment reference count
The DesignWare PCIe MSI hardware does not support MSI-X IRQs. Setting
those up failed as a side effect of a bug which was fixed by 91f8ae823f
("PCI: designware: Setup and clear exactly one MSI at a time").
Now that this bug is fixed, MSI-X IRQs need to be rejected explicitly;
otherwise devices trying to use them may end up with incorrectly working
interrupts.
Fixes: 91f8ae823f ("PCI: designware: Setup and clear exactly one MSI at a time")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
CC: stable@vger.kernel.org # v3.18+
Function pdc_detect_pll_input_clock uses 'struct timeval'
to measure start and end times, used to compute the pll_clock value.
'struct timeval' on 32-bit systems will have its tv_sec field
overflow in year 2038 and beyond. This patch uses 'ktime_t'
(which uses 64 bits for seconds) for start and end times instead.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The purpose of the functions and their parametrs might not be obvious
to the reader, so explain it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first parameter of __uvcg_iter_strm_cls() is always used in
the context of struct uvcg_streaming_header, so change the
function prototype accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although on some systems va_end is a no-op, it is good practice
to use va_end, especially since the manual states:
"Each invocation of va_start() must be matched by a corresponding
invocation of va_end() in the same function."
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
There is a request from IC engineer that if we doesn't
set phypwd as 0xffffffff, we need to delay about five
32Khz cycles before set phy's pwd register, otherwise,
the wakeup signal may can't wake up controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
At very rare cases, the SoF will not send out after resume with
low speed connection. The workaround is do not power down
PWD.RXPWD1PT1 bit during the suspend.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For non-otg mode, we keep the usage of disconnect line between phy analog
and digital unchanging; for otg mode, at peripheral role, we keep the usage
unchanging too, at host role, the digital part needs to know dp/dm change
to respond device's data pulse when it is at low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The RLT code has already done it, so no software operation is needed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1760 driver registration function returns an error if USB is
disabled. This made sense when the driver only supported host
controllers, but now that it supports peripheral controllers host
support isn't mandatory anymore.
Fix this by returning an error only when both the HCD and UDC functions
are disabled, either through the kernel configuration or at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both isp1760_register() and isp1761_pci_probe() check whether USB is
disabled by calling usb_disabled(), and bail out with an error if it is.
One check is enough, remove the PCI-specific check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable compilation of the isp1760 driver in pure host mode, pure device
mode, or dual-role mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that this is DRD, it doesn't make sense to keep it under
drivers/usb/host.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ISP1761 is a dual-mode host and device controller backward
compatible on the host side with the ISP1760. Add support for the device
controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Configuring the mode of operation of port 1 doesn't belong to the HCD
code, as it's related to the soon to come UDC support. Move the
configuration to core code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although the corresponding register is part of the HCD register space,
processor bus initialization is not specific to the HCD. To prepare for
device controller support, move bus interface initialization to core
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The IRQF_SHARED flag needs to be set regardless of the bus type. Don't
require glue code to set it manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move core device initialization to a central location in order to share
it with the device mode implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1760-rhcd.h header contains PTD constants and structures only
useful for the HCD implementation. It also contains register definitions
that will be needed by common code when implementing support for the
ISP1761 device controller, but doesn't contain the isp1760_hcd structure
definition that will also be used by common code.
Move definitions to the right location and create an isp1760-regs.h to
store register definitions. No change other than moving definitions and
modifying indentation is performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The slotinfo and memory_chunk structures are specific to the driver and
defined in a header file. Prefix them with isp1760_ to avoid namespace
clashes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate the driver private data structure manually instead of using the
usb_hcd private space. This will allow skipping hcd registration for the
isp1761 when used in device mode only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move the initialization code out of the PCI probe function to a new
function in order to simplify and fix error handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This simplifies error and remove code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function takes quite a few arguments, passing the resource pointer
instead of the start address and length simplifies it a bit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The argument is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The two functions are specific to the driver but have very generic
names, subject to collisions. Rename them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
