[ Upstream commit b7c3ca3553d1de5e86c85636828e186d30cd0628 ]
The value of 'ret' is zero when of_hte_req_count() fails to get number
of entitties to timestamp. And returning success(zero) on this failure
path is incorrect.
Fixes: 9a75a7cd03 ("hte: Add Tegra HTE test driver")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da8a635436029957c5350da3acf51d78ed64071 ]
When the lock bit inside SCH5627_REG_CTRL is set, then the virtual
registers become read-only until the next power cycle.
Disallow write access to those registers in such a case.
Tested on a Fujitsu Esprimo P720.
Fixes: aa9f833dfc ("hwmon: (sch5627) Add pwmX_auto_channels_temp support")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f0b28e0653f36b51542d25dd54ed312c397ecfc ]
Use bit macros then accessing SCH5627_REG_CTRL, so that people
do not need to look at the datasheet to find out what each bit
does.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stable-dep-of: 7da8a6354360 ("hwmon: (sch5627) Disallow write access if virtual registers are locked")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d621a46d05107f4e510383d6a38f2160c62d28f7 ]
This reverts commit 393935baa4.
As reported by Ian Nartowicz, this and the next patch
result in a failure to load the driver on Celsius W280.
While the alternative would be to add the board to the DMI
override table, it is quite likely that other systems are
also affected. Revert the offending patches to avoid future
problems.
Fixes: 393935baa4 ("hwmon: (sch56xx-common) Add automatic module loading on supported devices")
Reported-by: Ian Nartowicz <deadbeef@nartowicz.co.uk>
Closes: https://lore.kernel.org/linux-hwmon/20231025192239.3c5389ae@debian.org/T/#t
Cc: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28da9dee3594423534f3ea1e1f61e6bb2d2fa651 ]
This reverts commit fd2d53c367.
As reported by Ian Nartowicz, this and the preceding patch
result in a failure to load the driver on Celsius W280.
While the alternative would be to add the board to the DMI
override table, it is quite likely that other systems are
also affected. Revert the offending patches to avoid future
problems.
Fixes: fd2d53c367 ("hwmon: (sch56xx-common) Add DMI override table")
Reported-by: Ian Nartowicz <deadbeef@nartowicz.co.uk>
Closes: https://lore.kernel.org/linux-hwmon/20231025192239.3c5389ae@debian.org/T/#t
Cc: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfff736d30e5283ad09e748caff979d75ddef7f ]
When build with W=1 and "-Werror=format-truncation", below error is
observed in coretemp driver,
drivers/hwmon/coretemp.c: In function 'create_core_data':
>> drivers/hwmon/coretemp.c:393:34: error: '%s' directive output may be truncated writing likely 5 or more bytes into a region of size between 3 and 13 [-Werror=format-truncation=]
393 | "temp%d_%s", attr_no, suffixes[i]);
| ^~
drivers/hwmon/coretemp.c:393:26: note: assuming directive output of 5 bytes
393 | "temp%d_%s", attr_no, suffixes[i]);
| ^~~~~~~~~~~
drivers/hwmon/coretemp.c:392:17: note: 'snprintf' output 7 or more bytes (assuming 22) into a destination of size 19
392 | snprintf(tdata->attr_name[i], CORETEMP_NAME_LENGTH,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
393 | "temp%d_%s", attr_no, suffixes[i]);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Given that
1. '%d' could take 10 charactors,
2. '%s' could take 10 charactors ("crit_alarm"),
3. "temp", "_" and the NULL terminator take 6 charactors,
fix the problem by increasing CORETEMP_NAME_LENGTH to 28.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes: 7108b80a54 ("hwmon/coretemp: Handle large core ID value")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310200443.iD3tUbbK-lkp@intel.com/
Link: https://lore.kernel.org/r/20231025122316.836400-1-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a5b3370a1d9750eca325292e291c8c7cb8cf2e0 ]
axi_fan_control_irq_handler(), dependent on the private
axi_fan_control_data structure, might be called before the hwmon
device is registered. That will cause an "Unable to handle kernel
NULL pointer dereference" error.
Fixes: 8412b410fa ("hwmon: Support ADI Fan Control IP")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231025132100.649499-1-nuno.sa@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eba9ac7abab91c8f6d351460239108bef5e7a0b6 ]
Since commit fa1f68db6c ("drivers: misc: pass miscdevice pointer via
file private data"), the miscdevice stores a pointer to itself inside
filp->private_data, which means that private_data will not be NULL when
wmi_char_open() is called. This might cause memory corruption should
wmi_char_open() be unable to find its driver, something which can
happen when the associated WMI device is deleted in wmi_free_devices().
Fix the problem by using the miscdevice pointer to retrieve the WMI
device data associated with a char device using container_of(). This
also avoids wmi_char_open() picking a wrong WMI device bound to a
driver with the same name as the original driver.
Fixes: 44b6b76611 ("platform/x86: wmi: create userspace interface for drivers")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-5-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed85891a276edaf7a867de0e9acd0837bc3008f2 ]
When a WMI device besides the first one somehow fails to register,
retval is returned while still containing a negative error code. This
causes the ACPI device fail to probe, leaving behind zombie WMI devices
leading to various errors later.
Handle the single error path separately and return 0 unconditionally
after trying to register all WMI devices to solve the issue. Also
continue to register WMI devices even if some fail to allocate memory.
Fixes: 6ee50aaa9a ("platform/x86: wmi: Instantiate all devices before adding them")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-4-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d6e24b422a2166a9297a8286ff2e6ab9a5e8cd3 ]
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference.
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230901024658.23405-1-jiasheng@iscas.ac.cn
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2befa515c1bb6cdd33c262b909d93d1973a219aa ]
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference.
Fixes: 3b5e748615 ("clk: mediatek: add clock support for MT7629 SoC")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230912093407.21505-5-jiasheng@iscas.ac.cn
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0884393c63cc9a1772f7121a6645ba7bd76feeb9 ]
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference.
Fixes: 3b5e748615 ("clk: mediatek: add clock support for MT7629 SoC")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230912093407.21505-4-jiasheng@iscas.ac.cn
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606f6366a35a3329545e38129804d65ef26ed7d2 ]
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference.
Fixes: 96596aa066 ("clk: mediatek: add clk support for MT6797")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230912093407.21505-3-jiasheng@iscas.ac.cn
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f57f78fbacf630430bf954e5a84caafdfea30c0 ]
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference.
Fixes: 710774e048 ("clk: mediatek: Add MT6779 clock support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230912093407.21505-2-jiasheng@iscas.ac.cn
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b82681042724924ae3ba0f2f2eeec217fa31e830 ]
Add the check for the return value of mtk_alloc_clk_data() in order to
avoid NULL pointer dereference.
Fixes: 1aca9939bf ("clk: mediatek: Add MT6765 clock support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230912093407.21505-1-jiasheng@iscas.ac.cn
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7af5b9eadd64c9e02a71f97c45bcdf3b64841f6b ]
The "div" pointer is freed in _register_divider() and again in
of_ti_divider_clk_setup(). Delete the free in _register_divider()
Fixes: fbbc185915 ("clk: ti: divider: cleanup _register_divider and ti_clk_get_div_table")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/6d36eeec-6c8a-4f11-a579-aa3cd7c38749@moroto.mountain
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3400d546a741a2b2001d88e7fa29110d45a3930d ]
The ti_clk_register() and ti_clk_register_omap_hw() functions are always
called with the parameter of type "struct device" set to NULL, since the
functions from which they are called always have a parameter of type
"struct device_node". Replacing "struct device" type parameter with
"struct device_node" will allow you to register a TI clock to the common
clock framework by taking advantage of the facilities provided by the
"struct device_node" type. Further, adding the "of_" prefix to the name
of these functions explicitly binds them to the "struct device_node"
type.
The patch has been tested on a Beaglebone board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221113181147.1626585-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: 7af5b9eadd64 ("clk: ti: fix double free in of_ti_divider_clk_setup()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3aa5cb264a38ae9bbcce32abca4c155af0456df ]
AHB memory as MMIO should be mapped with ioremap rather than ioremap_wc,
which should have been used initially just to handle unaligned access as
a workaround.
Fixes: d166a73503 ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20231010201524.2021340-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84aefafe6b294041b7fa0757414c4a29c1bdeea2 ]
Fix spelling of "Structure".
Fix multiple kernel-doc warnings:
clk-provider.h:269: warning: Function parameter or member 'recalc_rate' not described in 'clk_ops'
clk-provider.h:468: warning: Function parameter or member 'parent_data' not described in 'clk_hw_register_fixed_rate_with_accuracy_parent_data'
clk-provider.h:468: warning: Excess function parameter 'parent_name' description in 'clk_hw_register_fixed_rate_with_accuracy_parent_data'
clk-provider.h:482: warning: Function parameter or member 'parent_data' not described in 'clk_hw_register_fixed_rate_parent_accuracy'
clk-provider.h:482: warning: Excess function parameter 'parent_name' description in 'clk_hw_register_fixed_rate_parent_accuracy'
clk-provider.h:687: warning: Function parameter or member 'flags' not described in 'clk_divider'
clk-provider.h:1164: warning: Function parameter or member 'flags' not described in 'clk_fractional_divider'
clk-provider.h:1164: warning: Function parameter or member 'approximation' not described in 'clk_fractional_divider'
clk-provider.h:1213: warning: Function parameter or member 'flags' not described in 'clk_multiplier'
Fixes: 9fba738a53 ("clk: add duty cycle support")
Fixes: b2476490ef ("clk: introduce the common clock framework")
Fixes: 2d34f09e79 ("clk: fixed-rate: Add support for specifying parents via DT/pointers")
Fixes: f5290d8e4f ("clk: asm9260: use parent index to link the reference clock")
Fixes: 9d9f78ed9a ("clk: basic clock hardware types")
Fixes: e2d0e90fae ("clk: new basic clk type for fractional divider")
Fixes: f2e0a53271 ("clk: Add a basic multiplier clock")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Link: https://lore.kernel.org/r/20230930221428.18463-1-rdunlap@infradead.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2b23159499efd36b2d63b3c4534075d12ddc97a ]
According to the hardware manual for RZ/G2L
(r01uh0914ej0130-rzg2l-rzg2lc.pdf), the computation formula for PLL rate
is as follows:
Fout = ((m + k/65536) * Fin) / (p * 2^s)
and k has values in the range [-32768, 32767]. Dividing k by 65536 with
integer arithmetic gives zero all the time, causing slight differences
b/w what has been set vs. what is displayed. Thus, get rid of this and
decompose the formula before dividing k by 65536.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-6-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf51d3b2d048c312764a55d91d67a85ee5535e31 ]
The onitial value of the CPG_PL2SDHI_DSEL bits 0..1 or 4..6 is 01b. The
hardware user's manual (r01uh0914ej0130-rzg2l-rzg2lc.pdf) specifies that
setting 0 is prohibited. Hence rzg2l_cpg_sd_clk_mux_get_parent() should
just read CPG_PL2SDHI_DSEL, trust the value, and return the proper clock
parent index based on the value read.
Fixes: eaff33646f ("clk: renesas: rzg2l: Add SDHI clk mux support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-5-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2692ed490e680a41401cef879adebcfafb4298f ]
The SD MUX output (SD0) is further divided by 4 in G2{L,UL}. The
divided clock is SD0_DIV4. SD0_DIV4 is registered with
CLK_SET_RATE_PARENT which means a rate request for it is propagated to
the MUX and could reach rzg2l_cpg_sd_clk_mux_set_parent() concurrently
with the users of SD0.
Add proper locking to avoid concurrent accesses on SD MUX set rate
registers.
Fixes: eaff33646f ("clk: renesas: rzg2l: Add SDHI clk mux support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-4-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5252d9697a3e7007c741e9c103073868955a304 ]
The clock dividers might be used with clock stop bit enabled or not.
Current tables only support recommended values from the datasheet. This
might result in warnings like below because no valid clock divider is
found. Resulting in a 0 divider.
There are Renesas ARM Trusted Firmware version out there which e.g.
configure 0x201 (shifted logical right by 2: 0x80) and with this match
the added { STPnHCK | 0, 1 }:
https://github.com/renesas-rcar/arm-trusted-firmware/blob/rcar_gen3_v2.3/drivers/renesas/rcar/emmc/emmc_init.c#L108
------------[ cut here ]------------
sd1h: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set
WARNING: CPU: 1 PID: 1 at drivers/clk/clk-divider.c:141 divider_recalc_rate+0x48/0x70
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.52 #1
Hardware name: Custom board based on r8a7796 (DT)
pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : divider_recalc_rate+0x48/0x70
...
------------[ cut here ]------------
Fixes: bb6d3fa98a ("clk: renesas: rcar-gen3: Switch to new SD clock handling")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
[wsa: extended the table to 5 entries, added comments, reword commit message a little]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230928080317.28224-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15cee75dacb82ade710d61bfd536011933ef9bf2 ]
Move the elcdif_pll clock initialization before the lcd_clk, since the
elcdif_clk needs to be initialized ahead of lcd_clk, being its parent.
This change fixes issues with the LCD clocks during suspend/resume.
Fixes: babfaa9556 ("clk: imx: scu: add more scu clocks")
Suggested-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Acked-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230912-imx8-clk-v1-v1-2-69a34bcfcae1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 577ad169966e6e75b10e004389a3f79813e84b5d ]
Avoid memory leak in error handling path. It does not make
much sense for the SoC without clk driver, to make program behavior
correct, let's fix it.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202309240551.e46NllPa-lkp@intel.com/
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20231001122618.194498-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 317e69c49b4ceef8aebb47d771498ccb3571bdf9 ]
If the i.MX8QXP clock provider is built-in but the MXC_CLK is
built as module, build fails:
aarch64-linux-ld: drivers/clk/imx/clk-imx8-acm.o: in function `imx8_acm_clk_probe':
clk-imx8-acm.c:(.text+0x3d0): undefined reference to `imx_check_clk_hws'
Fix that by selecting MXC_CLK in case of CLK_IMX8QXP.
Fixes: c2cccb6d0b ("clk: imx: add imx8qxp clk driver")
Closes: https://lore.kernel.org/all/8b77219e-b59e-40f1-96f1-980a0b2debcf@infradead.org/
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7442edec72bc657e6ce38ae01de9f10e55decfaa ]
The MT6358 and MT6366 PMICs, and likely many others from MediaTek, have
a chip ID register, making the chip semi-discoverable.
The driver currently supports two PMICs and expects to be probed on one
or the other. It does not account for incorrect mfd driver entries or
device trees. While these should not happen, if they do, it could be
catastrophic for the device. The driver should be sure the hardware is
what it expects.
Make the driver fail to probe if the chip ID presented is not a known
one.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: f0e3c6261a ("regulator: mt6366: Add support for MT6366 regulator")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230913082919.1631287-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fc62c8347397faf4e18249e88ecd4470c0a5357 ]
The SMMU GDSC doesn't have to be ALWAYS-ON and shouldn't feature the
HW_CTRL flag (it's separate from hw_ctrl_addr). In addition to that,
it should feature a cxc entry for bimc_smmu_axi_clk and be marked as
votable.
Fix all of these issues.
Fixes: d14b15b593 ("clk: qcom: Add MSM8998 Multimedia Clock Controller (MMCC) driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20230531-topic-8998_mmssclk-v3-5-ba1b1fd9ee75@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9906c4140897bbdbff7bb71c6ae67903cb9954ce ]
Some branch clocks are governed externally and we're only supposed to
send a request concerning their shutdown, not actually ensure it happens.
Use the BRANCH_HALT_SKIP define to skip checking the halt bit.
Fixes: d14b15b593 ("clk: qcom: Add MSM8998 Multimedia Clock Controller (MMCC) driver")
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230531-topic-8998_mmssclk-v3-4-ba1b1fd9ee75@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7b7d30158cff246667273bd2a62fc93ee0725d2 ]
If the parent clock rate is greater than unsigned long max/2 then
integer overflow happens when calculating the clock rate on 32-bit systems.
As RCG2 uses half integer dividers, the clock rate is first being
multiplied by 2 which will overflow the unsigned long max value.
Hence, replace the common pattern of doing 64-bit multiplication
and then a do_div() call with simpler mult_frac call.
Fixes: bcd61c0f53 ("clk: qcom: Add support for root clock generators (RCGs)")
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230901073640.4973-1-quic_devipriy@quicinc.com
[bjorn: Also drop unnecessary {} around single statements]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4afda5f6bcdf673ef2556fcfa458daf3a5a648d8 ]
The GCC driver contains clocks that are owned (meaning configured and
scaled) by the RPM core.
Remove them from Linux to stop interjecting the RPM's logic.
Fixes: b1e010c073 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230830-topic-rpmbusclocks8996gcc-v1-1-9e99bedcdc3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb9913b511f10968a02cfa5329a896855dd152a3 ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Fix this by stop calling request_irq() with invalid IRQ #s.
Fixes: dc4dc36056 ("spi: tegra: add spi driver for SLINK controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/tencent_73FCC06A3D1C14EE5175253C6FB46A07B709@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3601857e14de6369f00ae19564f1d817d175d19 ]
This error handling looks really strange.
Check if the string has been truncated instead.
Fixes: f0c2319f9f ("regmap: Expose the driver name in debugfs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/8595de2462c490561f70020a6d11f4d6b652b468.1693857825.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff672b9ffeb3f82135488ac16c5c5eb4b992999b ]
Both ipvlan_process_v4_outbound() and ipvlan_process_v6_outbound()
increment dev->stats.tx_errors in case of errors.
Unfortunately there are two issues :
1) ipvlan_get_stats64() does not propagate dev->stats.tx_errors to user.
2) Increments are not atomic. KCSAN would complain eventually.
Use DEV_STATS_INC() to not miss an update, and change ipvlan_get_stats64()
to copy the value back to user.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Link: https://lore.kernel.org/r/20231026131446.3933175-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b068c714ca9479d2783cc333fff5bc2d4a6d45c ]
Companion of DEV_STATS_INC() & DEV_STATS_ADD().
This is going to be used in the series.
Use it in macsec_get_stats64().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ff672b9ffeb3 ("ipvlan: properly track tx_errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03d6c848bfb406e9ef6d9846d759e97beaeea113 ]
When the ipv6 stack output a GSO packet, if its gso_size is larger than
dst MTU, then all segments would be fragmented. However, it is possible
for a GSO packet to have a trailing segment with smaller actual size
than both gso_size as well as the MTU, which leads to an "atomic
fragment". Atomic fragments are considered harmful in RFC-8021. An
Existing report from APNIC also shows that atomic fragments are more
likely to be dropped even it is equivalent to a no-op [1].
Add an extra check in the GSO slow output path. For each segment from
the original over-sized packet, if it fits with the path MTU, then avoid
generating an atomic fragment.
Link: https://www.potaroo.net/presentations/2022-03-01-ipv6-frag.pdf [1]
Fixes: b210de4f8c ("net: ipv6: Validate GSO SKB before finish IPv6 processing")
Reported-by: David Wragg <dwragg@cloudflare.com>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Link: https://lore.kernel.org/r/90912e3503a242dca0bc36958b11ed03a2696e5e.1698156966.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48cf49d31994ff97b33c4044e618560ec84d35fb ]
snprintf() does not return negative values on error.
To know if the buffer was too small, the returned value needs to be
compared with the length of the passed buffer. If it is greater or
equal, the output has been truncated, so add checks for the truncation
to create_pnp_modalias() and create_of_modalias(). Also make them
return -ENOMEM in that case, as they already do that elsewhere.
Moreover, the remaining size of the buffer used by snprintf() needs to
be updated after the first write to avoid out-of-bounds access as
already done correctly in create_pnp_modalias(), but not in
create_of_modalias(), so change the latter accordingly.
Fixes: 8765c5ba19 ("ACPI / scan: Rework modalias creation when "compatible" is present")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ rjw: Merge two patches into one, combine changelogs, add subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d35381aa73f7e1e8b25f3ed5283287a64d9ddff5 ]
htab_lock_bucket uses the following logic to avoid recursion:
1. preempt_disable();
2. check percpu counter htab->map_locked[hash] for recursion;
2.1. if map_lock[hash] is already taken, return -BUSY;
3. raw_spin_lock_irqsave();
However, if an IRQ hits between 2 and 3, BPF programs attached to the IRQ
logic will not able to access the same hash of the hashtab and get -EBUSY.
This -EBUSY is not really necessary. Fix it by disabling IRQ before
checking map_locked:
1. preempt_disable();
2. local_irq_save();
3. check percpu counter htab->map_locked[hash] for recursion;
3.1. if map_lock[hash] is already taken, return -BUSY;
4. raw_spin_lock().
Similarly, use raw_spin_unlock() and local_irq_restore() in
htab_unlock_bucket().
Fixes: 20b6cc34ea ("bpf: Avoid hashtab deadlock with map_locked")
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/7a9576222aa40b1c84ad3a9ba3e64011d1a04d41.camel@linux.ibm.com
Link: https://lore.kernel.org/bpf/20231012055741.3375999-1-song@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 658939fc68d3241f9a0019e224cd7154438c23f2 ]
If a TX queue has no space for new TX frames, the driver will keep
these frames in the overflow queue, and during reclaim flow it
will retry to send the frames from that queue.
But if the reclaim flow was invoked from TX queue flush, we will also
TX these frames, which is wrong as we don't want to TX anything
after flush.
This might also cause assert 0x125F when removing the queue,
saying that the driver removes a non-empty queue
Fix this by TXing the overflow queue's frames only if we are
not in flush queue flow.
Fixes: a445098058 ("iwlwifi: move reclaim flows to the queue file")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.caf06c8709d9.Ibf664ccb3f952e836f8fa461ea58fc08e5c46e88@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37fb29bd1f90f16d1abc95c0e9f0ff8eec9829ad ]
When we want to synchronize the NAPI, which was added in
commit 5af2bb3168db ("wifi: iwlwifi: call napi_synchronize()
before freeing rx/tx queues"), we also need to make sure we
can't actually reschedule the NAPI. Yes, this happens while
interrupts are disabled, but interrupts may still be running
or pending. Also call iwl_pcie_synchronize_irqs() to ensure
we won't reschedule the NAPI.
Fixes: 4cf2f5904d ("iwlwifi: queue: avoid memory leak in reset flow")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.a0f4104b479a.Id5c50a944f709092aa6256e32d8c63b2b8d8d3ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5af2bb3168db6b0af9988eb25cccf2e3bc4455e2 ]
When rx/tx queues are being freed, on a different CPU there could be
still rx flow running. Call napi_synchronize() to prevent such a race.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Co-developed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://lore.kernel.org/r/20230416154301.5171ee44dcc1.Iff18718540da412e084e7d8266447d40730600ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 37fb29bd1f90 ("wifi: iwlwifi: pcie: synchronize IRQs before NAPI")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73ed8e03388d16c12fc577e5c700b58a29045a15 ]
cookie_init_timestamp() is supposed to return a 64bit timestamp
suitable for both TSval determination and setting of skb->tstamp.
Unfortunately it uses 32bit fields and overflows after
2^32 * 10^6 nsec (~49 days) of uptime.
Generated TSval are still correct, but skb->tstamp might be set
far away in the past, potentially confusing other layers.
tcp_ns_to_ts() is changed to return a full 64bit value,
ts and ts_now variables are changed to u64 type,
and TSMASK is removed in favor of shifts operations.
While we are at it, change this sequence:
ts >>= TSBITS;
ts--;
ts <<= TSBITS;
ts |= options;
to:
ts -= (1UL << TSBITS);
Fixes: 9a568de481 ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d9ddbacb102621af6d28ff7bf5a0b4ce249d8 ]
tp->rcv_tstamp should be set to tcp_jiffies, not tcp_time_stamp().
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
